Hello everyone!!

Ok, on this short video I am showing my Winding Spool Pattern for ALL the Sequential Coils...


Happy 2025!!

Ufopolitics

Hello to All,

Ok, I am working now on the Sequential Coils wires Length versus Resistance...

First on the first Spool of 23 Gauge wire and according to the CIRRIS WIRE RESISTANCE CALCULATOR (<<link on Title)

On this Calculator above, We set the LENGTH and GAUGE, and it calculates the RESISTANCE. And this Method is the one that I conducted previously, see image attached:


And it gave exactly 6.251 Ohms on 307 Feet of 23 Gauge Wire.

However, when we use the same CIRRIS Calculator Site, but to Estimate based on the LENGTH of Wire : CIRRIS WIRE LENGTH CALCULATOR (<<Link)

On this Calculator we provide RESISTANCE and GAUGE of wire, and it gives us the LENGTH (see image below)


And as you could see, the Calculator above gives us a RANGE of Wire Length (297 - 328 feet), which is not precise at all, even with the FOUR Wires Resistance Meter (which is the one I have, and is the more accurate available so far)

Anyways I went ahead and on the FIRST SPOOL, I cut exactly 307 Feet of 23 Gauge, PLUS about One (1) Feet extra for the connections or 6 inches on each side of coil terminals.

And on Image below is shown the results:


In conclusion that the Calculated measurements are PERFECT, so NOW I can go ahead and keep cutting 307 feet + One Feet more for terminal connections.

ALWAYS, whenever you have to make several coils, which ALL are based on the exact Resistance Value, Cut FIRST ONE then measure it, before proceeding to keep on the following ones...

On another note: previously on the Sequential Driver Topic I had some comments about changing Sequential Coils #1 and #8 (lowering resistance), due that Member Grey Wolf 47 found out some small issues with the Solid-State Driver versus the original Figuera Sequence that REPEATS #1 & #8 to DELAY Timing and so BALANCE with the rest of coils timings...

So,I have decided to make ALL SEQUENTIAL COILS with the SAME Resistance or 6.25 Ohms EACH COIL.

After going over the changing/dropping of resistance just on coils #1 &#8, this creates an UNBALANCE of the WHOLE Resistance in the GROUP of EIGHT COILS that are ALWAYS to be ON during the Sequence.

And I do NOT want to do that, because that will make the Currents also Fluctuate during sequencing...And I want ALL THREE PARAMETERS (V & R & I) to keep ALWAYS within the SAME VALUES. And that is V=50V, R= 50 Ohms, I= 1.0 Amp. This guarantees that Field Strength (basically, but along other field parameters like Volume, Density, Propagation properties, etc) will REMAIN EXACTLY the same during SPACETIME travel of this Virtual Field.

This is KEY for this Test to be successful!!

Regards

Ufopolitics

Ufopolitics

Hello All,

Ok, on all previous Video-Images-Posts, I just wanted to give you all a basic GRAPHIC idea about how easy is to build this setup whenever putting together your device.

So, up to here I will just keep cutting and winding wire to keep building all the Fifteen Sequential Coils (a very TEDIOUS job!!) and it does not mean that I will upload a video for every coil I finish...it will be very "boring" since it is the same procedure, over and over...

I will STOP when finishing Coil#8, in order to perform the Tests that I have mentioned previously about Field Propagation and Strength, using the Digital Meter I also have shown and that I have already purchased.

Then I will upload a Video and Images dedicated to those readings, as I will recall that previous post as well.

I will NOT build anytime soon the Second Secondaries at each extreme of Linear Steel Core, until I have run first ALL 15 Sequential Coils along Main Primary.

So, here is my schedule related to this setup so far.

Regards

Ufopolitics

Quote from: Ufopolitics on Jan 26, 2025, 11:38 AMI will STOP when finishing Coil#8,...........

What an incredible amount of work. I really hope you will achieve results now, especially considering all those previous attempts and disappointments. What perseverance! respect!!
Kind regards,
Leonard.