@rakarskiy.

Ok, I do not think you have understood correctly how my design works...as many more here may, so, just in case...I will "brake it down" in two parts:

1- First, the Dynamo (Generator) Part alone.

So, below is just the Dynamo part, MODIFIED:



Ok, so, above is just a "typical" Two Pole, Automotive Dynamo, that I had ONLY MODIFIED the TWO STATORS.

NOT the Brushes (still at 180º)

NOT the Armature.

And by modifying the TWO STATORS, AS SHOWN ABOVE, I am FORCING (BENDING) the LINES of Force to be as shown above in the blue curved lines, travelling from North to South Stators.

Then, if you just rotate this Dynamo, it will still be generating power, collected at the two brushes.

However, the LEFT SIDE OF ARMATURE will NOT be generating nothing (IDLING SIDE). Since there are no Stator Fields there...NO Lines of Force= NO INDUCTION.

So, you get Positive Output at Brush D, and Negative Output at Brush C.

AND MORE IMPORTANTLY...YOU CAN STILL RUN THIS DYNAMO AS A MOTOR!!

1- If the Magnetic Field developed at HALF Armature is NORTH (BLUE) then it will run CCW

2- If the Magnetic Field developed at that same HALF Armature is SOUTH (RED) it will spin CW.

It will run very MECHANICALLY UMBALANCED though, but it will definitively run!!

I guarantee it will run as a motor, and as a Dynamo, it will generate power as well, maybe not the full power output it had, when the FULL ARMATURE was generating power with the two stators at 180 degrees, but the difference will not be that much.

We may need to increase speed to compensate output volume.


Ufopolitics

Hello again,

Ok, and here is just the SIMPLE MOTOR SIDE:



Here Motor will run CW, and by just moving (A FEW DEGREES) the TWO BRUSHES (A & B) below S1 BISECTOR LINE, we will get it to REVERSE DIRECTION, or CCW.

Without the need to reverse the electrical polarities of motor brushes.

As we can expand this INTERACTION ANGLE BETWEEN BRUSHES, to have less currents on Armature or decrease Angle to gain more power on Armature...

Yes, it is "very asymmetrical", and Yes, it will run very UNBALANCED BY ITSELF!!

NOW, if we are going to see the whole thing, we must realize THERE IS ANOTHER FIELD ON THIS MOTOR ARMATURE, EXACTLY AT 180 DEGREES FROM THE INTERACTING ANGLE:


So, this opposite side angle is WIDER, as it comprehends MORE COILS on ARMATURE that the Blue one, hence, it is WEAKER, as it has more resistance and lesser currents.

This Red Angle is also of OPPOSITE POLARIZATION than Blue Angle, so, if Blue is North, then Red is South.

And here (on this same SPACE as Red Motor Angle) comes the Generator side Angle...that here MUST BE OF THE SAME POLARITY as the Motor Angle, so they both FUSE TOGETHER as ONE.

IF THEY ARE OPPOSITE IN MAGNETIC POLARITY, THEY WILL CANCEL OR DOMINATES A SUBTRACTED DIFFERENCE, DEPENDING ON WHICH ONE IS STRONGER...this will NOT WORK!!

THEY MUST BE OF THE SAME POLARITY FOR THE BLENDING*, THE FUSION* TO TAKE PLACE SMOOTHLY!!

* When I say "BLEND AND FUSE" I mean that since BOTH Fields are manifesting on the SAME WIRES on ARMATURE, by being of same magnetic polarization, it means currents will run on the same direction flow.
Then currents WILL ADD within the Armature Wires on this Red side.



So, it is supposed that Motor runs with the other side GENERATING SIDE ASSISTANCE, in order that:

BETWEEN BOTH DEVICES (MOTOR AND GENERATOR) WE MUST FIND A WAY, THAT THEY WILL "ASSIST" EACH OTHER'S, THIS IS THE "WHOLE SECRET" HERE.

So, once we load generator, a Magnetic Field would be generated on armature, on the generating side ONLY.

And that Field needs to ASSIST MOTOR ROTATION!!!

NOW, there are A LOT, AND I MEAN "A LOT" of Parameters here to ADJUST and play with them, in order to get the whole SYSTEM to run very smoothly, AND THAT IT WORKS BEAUTIFULLY AS EXPECTED.

This is the way I see it...and this is the way I will test it whenever I am ready to do it.

If it does not work, well, it would be another way we know it will not work...

That's all folks!!

Regards

Ufopolitics

Hello again,

This Three Stators Lockridge Design is just a way to see, understand and build this Machine on the simplest way possible.

However, on the Motor Side, instead of just one stator S1, there could be TWO SMALLER Motor Stators, like we have seen on the Lockridge Bedini's Video...BUT this will complicate -A LOT- the way of understanding this Device.

Since the Motor Angle would vary, plus the Generating side will also get Induction from these two motor stators (since they are North-South) they will also have an inducing field on the motor side.

So, if on the 3 Stators, there are a LOT of Parameters to play with, to get it running perfect...with Four Stators it is DOUBLE those Parameters at play.

And the chances for it to blend, fuse and work perfectly well are MUCH HARDER TO ACHIEVE.

That is the only reason why, I reduced this design into three stators to start testing it first.

Once we get positive results and get it to run beautiful...then we could build a Second Machine, (NEVER TAKE APART THE ONE IS WORKING!!) where all four stators are involved.

Sincerely


Ufopolitics

Quote from: Ufopolitics on Nov 25, 2024, 12:41 PMOnce we get positive results and get it to run beautiful...then we could build a Second Machine, (NEVER TAKE APART THE ONE IS WORKING!!) where all four stators are involved.

Hi Ufo. What you just said there is very true. Don't take it apart. Build another machine and do some testing on so you have all the parameters on that one.

The ones I have worked with are the 4 pole ones. Yes, they are very touchy. Seems like if one part is adjusted all the rest needs to be adjusted to compensate for the adjustment.

I like your approach to getting a wider angle of generation on the one side. If the bemf is a problem just shifting the brushes or the pole shoes might solve the problem. Won't know for sure until it proven.

Quote from: Ufopolitics on Nov 25, 2024, 11:07 AM

[...]

...NOW, if we are going to see the whole thing, we must realize THERE IS ANOTHER FIELD ON THIS MOTOR ARMATURE, EXACTLY AT 180 DEGREES FROM THE INTERACTING ANGLE:

So, this opposite side angle is WIDER, as it comprehends MORE COILS on ARMATURE that the Blue one, hence, it is WEAKER, as it has more resistance and lesser currents.

This Red Angle is also of OPPOSITE POLARIZATION than Blue Angle, so, if Blue is North, then Red is South.

[...]

*******************************

Hello All,

Ok I wanted to add this post after making this specific CAD, which will "resume" on all prior posts, before the day ends.

After looking at that Back Red Motor Angle & Bisector on the quoted post above...I want you to see what happens when I just add the two Generator Brushes.
(And I have not added on image below ANY Stators, not to deviate your attention on anything else, BUT all FOUR Brushes placement and the EFFECT IT CAUSES on the Armature Magnetic Field Angles.


And even if we do not power up the Generator stators...so there will not be any induction on the Red Angle side, this is what takes place.

Please compare both images and see the difference.

First, note that the Red Motor Angle gets "narrower" now defined by the two Generator Brushes being there and contacting commutator.

Like I wrote before, EVEN WITH THE GENERATOR STATORS OFF, this Red Angle will be RESHAPED just by having these two brushes at 180 degrees.

On this CAD I have the same Electrical Polarity as all prior Graphics on ALL BRUSHES. And between the Two Positive Brushes A & D, I have added a small coil joining these two brushes. I also have done the same thing below between lower Negative Brushes B & C.

And this means that the Positive and Negative Input charges on Motor Brushes A & B + C & D, are TRANSFERRING their charges through all coils on Armature on those TWO specific segments.

As a result, there will NOT BE ANY MAGNETIC FIELD GENERATED between those two segments, reason I wrote "NO FIELD" on both sides.

Also, please compare on BOTH IMAGES the TWO RED ARROW BISECTOR ON THE RED ANGLE...

It has moved from being perfectly aligned, straight with Blue Arrow Bisector on IMAGE 1, to become a straight 90º angle related to the new added Generator brushes set at 180º Line.

Again, this happens, even if the Generator side is completely OFF.

As when you turn Generator Stators ON, nothing would change related to these Two Angles positioning and Bisectors, on the contrary, the Generated Field Angle, once Output is loaded will COINCIDE EXACTLY ON THE SAME SPATIAL POSITIONING FOR BOTH (MOTOR-GEN) RED SIDE ANGLES.

Finally, even when you adjust the Two Motor Brushes A & B to change Motor Rotation, this Red Back Motor-Generator FUSED Angles and Bisectors will NOT SHIFT, NOR MOVE EVEN ONE MILLIMETER.

This is just the FIRST PART of this "FUSION" between these TWO ANGLES (Motor-Generator) starts right here...

Regards

Ufopolitics