FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello to All,

Ok, here I will start a sequence of images based on a Longitudinal Sectional Cut View, in order that You can have a "Layer's View" of ALL Coils, plus also of the Steel Cores...of just one Module of this Figuera Generator...

On this First Image, and starting from the very center:

1- Longitudinal Center Steel Core, (shaded in black) and this Core can be of ANY Shape or form...Square-Rectangular, Round-Cylindrical or else...on the Rectangular Shape it could be done with regular laminated steel, like in any Transformer...I am just starting my prototypes on a Round Cylindrical Core, because it is easier to cut and shape in a Lathe.

2- The Part "y" or the Induced, (in a yellow color) where we take our Output from, it wraps FIRST than all other coils directly to steel core.

3- The Part "N" and Part "S" located at each extreme end of steel core (in Gold [N] and Green respectively.

4- The First Sequence of Coils for Part "N" (in Gold): N1, N2, N3, N4, N5, N6, N7 in that firing order, from Left to Right.

5- The Second Sequence of Coils for Part "S" (in Green): S1, S2, S3, S4, S5, S6, S7, in that order they fire from Right to Left.

Note that when we add pins to make wiring connections, they get a different numbering sequence, that extends from 1-8 and 9-16, and that is because we start by attaching the end of each Primary to the First Coil on each sequence. Therefore, when adding Primaries, we have Eight plus Eight total coils.

So, on this image for easier understanding, I have given same sequence numbers from 1-7 to both Sequential Coils.

Anyways, I want you to realize that I am disclosing exactly the setup I am working on now.

It does not means -at all- that it can not be done differently, like using 20 commutator elements, or using rectangular steel laminations from an old transformer for the core(s)...etc,etc.

This Method will work on different Geometries, as long as you can fit all components there, and wire it accordingly.

It does not matter if your cores have "hexagon" (not round) cylindrical shape, or square, or rectangular, the Magnetic Field would still be generated SPATIALLY for ALL Geometries in the SAME SHAPE...

And, it must be on an Elongated Geometry, not in an Sphere shape of course! So, do not take "literally" when I wrote "any geometry"...


Regards

Ufopolitics

[Ufopolitics]

Hello All,

Ok, here I have the same image as I have in prior post, but here with all possibilities to add more Induced Coils that would be outputting from the same Magnetic Fields displacement.

I already explained that Magnetic Fields expands Spatially, beyond its physical originating Core-Coil, and so, this Electromagnetic Pulses would also be transferred into its Spacetime three dimensional volume.

This allows to add additional Secondaries in different positioning around its embodiment.

1- We have the original Part "y" that has been showed on previous posts.

2- Plus an Out most Coil "y 2"(above ALL the sequential Coils)

3- Plus a Right Side Coil "y 3" that could go above Primary S, or side by side will also work, (on this image is shown above S).

4- Plus a Left Side Coil "y 4" shown on the image on top of Primary N.

These last Two Induced Coils y3-y4, can be connected (wired) in series, as each of them would be getting majority of induction from the opposite Sequencing of Coils.
So, once connected in series, they will add up both Pulses.

One more thing...the Outer Cap Plates shown here, I have them in my setup, they are solid steel caps about 3/4 of an inch, that bolt to main inner steel cylinder core, and whenever I add them on, while running the generator, the output increases considerably.

Ok, and this is my final post for today, related to this Disclosure.

Regards

Ufopolitics

[Ufopolitics]

However, a thought and a suggestion for the future:

I don't think your circuit does exactly that. If you graph your circuit current as a sine wave it appears that your induction will peak at 90 deg then collapse to almost 0 and immediately start increasing on the negative side, also at 90 deg or there about. Then the current of opposite sign will increase to max at 180 deg then collapse back to 0 at 180 deg. In effect, 2 half sines.

Sorry, but I have to disagree with your analysis, if I am understanding well (and I may not)...

If the commutator segments were doubled a truer sine could be produced. Increase the connected coil segments from 1 to 8, then decrease one segment at a time back to the first. Then repeat the sequence for the opposite set of coils with the other half of the commutator segments. This should produce a full sine wave. The induced will output as the field is reduced just as it did while the field was increasing. A gradual decrease like this might also alleviate the sparking to a large extent when the inducing fields swap polarity.

Just something for you to think about.

Regards

Ok, Cadman,

My big time apologies!!

By the time you wrote your post, I was involved into posting the two more images that I uploaded before...and my head was not that clear to understand what you meant...
That is why I wrote then :  if I am understanding well (and I may not)...

Well, now I am sure I did not understand you AT ALL that first time...

Ok, after going over again and again on what you wrote above...I finally believe I understand it now (I hope so...lol)

What you meant is to leave the jumpers as Figuera had it originally...right?
Then you only get 8 contacts out...that sequence 1 through 8 (first 180º) and then go backwards or from 8 through 1 (in the other 180º)

And the way you want to do it, is using those eight contacts to BOTH Sequential Coils Group.

Except that one group of coils (say for N Primary) will be wired 1 through 8 and the other sequential group (for Primary S) would be wired from 8 through 1

I think I got it !!!

And just looking at it briefly...I think you are COMPLETELY RIGHT!!

And if it works, it will be AWESOME!!... just because none of the sequential groups will collapse all the sudden, but gradually and smoothly!!

And I will still have two independent Group of Sequentially driven Coils!!

SUPERB IDEA MY FRIEND!!...AWESOME!!

Next I will  put some CAD Connections...for Us to go over it...

Thanks!!

Best Regards

Ufopolitics

[citfta]

I also agree with your interpretation of what CADMAN posted.  I think it may work even better but only a real test will show if the caps somehow add to the induction process or if the process is better without them.  Great work guys!  

On another thought.  UFO, your cad drawings seem to indicate that the primaries are bigger than the sequential coils.  Is that correct?  I understand all the sequential coils need to be the same but can the primary coils be larger?

Regards,
Carroll

[Cadman]

Hi guys,

I meant actually use a 32 segment commutator.

I don't want to derail this thread or your build any more than I have, so I can explain it better when you open the thread for comments.

Ok?