Because the importance that this subject-topic has, I have dedicated a specific Category and a Specific Board to disclose this material...


Hello to ALL,

No matter about my personal situation, I could not hold on to post about this new development, that I have started a while back...just a "while" back.
So, I will start from the First and Simplest part...


We all know that by simply winding a single thread of wire (meaning, not a bifilar, or else) ...just a single wire...wound around a circular cylinder (just to pick a simple geometry)

And that "cylinder" could be made of a solid steel, or a hollow plastic piece, like a spool.

Well, the point is that no matter if it is an air or solid or laminated, steel core...whenever we add a DC Current (+/-) to the terminals of the ending wires, it automatically, generates a Magnetic Field...right?

(THE SINGULARITY) So, we also know all the studies behind this "phenomena"...like where is the Electric and the Magnetic Fields on that single wire...like in a 90 degrees alignment.

So, up to the above paragraphs, I have described the way a "typical coil" is made (very briefly) ...and it generates a Magnetic Field...

This Generated Magnetic Field produces a North and a South Pole, and if we trace a line between both magnetic poles Center, we get an Axis.

And so, this Pole Magnetic Axis is 'exactly' Perpendicular to our winding's 'loops' plane...As well as 'Parallel' to the whole coil cylindrical shape, Axis.

Hope you are all following me up to here...so far.... because it will get a bit more complicated from here on.


Ok, so here I will have to cite our first simple coil structure...based on a single wire...

But now, we will make that 'single wire conductor' as a very long and thin coil, as it was our 'single wire' conductor, except that now we will add a small steel wire as a center core.
Then we wind our coil around that center wire core...then we make a whole spool of that special type of 'coil-cored-wire'...




So, on above image we have:

A- A single wire (of any gauge) that we have normally used for over 200 plus years, to wind a simple 'COIL'

Then here is my proposal:

B- A 'Coil-Cored-Wire' that we will be using to REPLACE the typical Single Wire we have being using to make a 'Coil'

And here we can see:

1- The Steel Wire Core in Blue
2- The wound coil around that steel wire core

And the idea is so simple...

Instead of using the typical single wire to wind a Coil, this time, we are going to be using a 'Coil Cored Wire' instead...

To be continued...

Ufopolitics

Continuation...

Let's stop here and make some simple test:

Let's extend all that coiled cored wire, (with a centered steel core wire), in a straight line...we add DC Power on both ends, and we also get a Magnetic Field...except it is a very long field, all across the conductor length:



Yes, it is a very long and fine steel core coil...and it will render a very long Magnetic Field.

If we all understood up to here...then the rest is a piece of cake...

Ufopolitics

Hello All,

What we would be making/building here, has NEVER being done in our lifetime history...

We will 'literally' be 'Winding'/'Bending' around a 'Core', a Magnetic Field, following a 'Core' in 'Loops' of that 'Field'...

And this is just a 'Primary' Test...of a Single Coil...to see the 'Field' it generates...


Regards


Ufopolitics

Quote from: Ufopolitics on Jun 16, 2025, 01:07 AMhas NEVER being done in our lifetime history...

Some where buried in my piles and boxes of 1998 Q Tech Laboratory R&D junk, I have several of these Coiled wire coils.
I used mild steel wire as the inner core to be wrapped. I even used a 4mm iron pipe filled with boron and cobalt and crystal powders as the core to be wrapped before wrapping around a 'spool'.

The "Best" is to Braid 3 wires like one braids hair, and use this braided 3 wires to wrap the iron powder filled core. But a solid iron core works easily and is simple. The 3 wires are then connected to 3 DC power sources. IF they were connected to a Double Negative Battery source you would have a earth Field Repelling Field Coil.

Another way to wrap an iron wire core with a coil as a single wire is to take the long length of IRON ELECTRICAL wire (Tesla preferred iron over copper and all over unity enthusiasts should do likewise) and make a very long U shaped wire and wrap the iron core with this 'double' wire to create an Infinity Loop or virtual rotating Magnetic Field as the 'coil' wrapping the iron core.


regards MerLynn

Quote

Quotehas NEVER being done in our lifetime history...

Some where buried in my piles and boxes of 1998 Q Tech Laboratory R&D junk, I have several of these Coiled wire coils.
I used mild steel wire as the inner core to be wrapped. I even used a 4mm iron pipe filled with boron and cobalt and crystal powders as the core to be wrapped before wrapping around a 'spool'.

The "Best" is to Braid 3 wires like one braids hair, and use this braided 3 wires to wrap the iron powder filled core. But a solid iron core works easily and is simple. The 3 wires are then connected to 3 DC power sources. IF they were connected to a Double Negative Battery source you would have a earth Field Repelling Field Coil.

Another way to wrap an iron wire core with a coil as a single wire is to take the long length of IRON ELECTRICAL wire (Tesla preferred iron over copper and all over unity enthusiasts should do likewise) and make a very long U shaped wire and wrap the iron core with this 'double' wire to create an Infinity Loop or virtual rotating Magnetic Field as the 'coil' wrapping the iron core.


regards MerLynn

Hello MerLynn,

Well, it is great that you have tried a similar project that I was showing!!

Do you have any pictures of this project?

1- Did you take any Magnetic Polarity readings of the Main Core Field created within the wound Core of the Coil Cored Wire?

2- Or did you Visualize that Main Core Field with any known methods, say plain Magnetic Viewing Film, CRT Screening or Ferrocell?

3- Or did you run any interactions with other Magnetic Fields (PM´s), looking for Repulsions or Attractions with the Main Core Field?

Note: I call the ´Main Core Field´ to the Field originated INSIDE that Coil wound with the specific Coiled Steel Cored Wire (shown on my diagrams above).

Regards

Ufopolitics