FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

@ Ufopolitics,

Dear, please check Your email sent You the wiring diagram and BOM files.
If you did no receive these, let me know.

Greetings, Alex

Hello Kampen,

Yes, I received all the BOM Files (for all V1 & V2) and the interconnections Diagram between Boards for Version 2.

Many thanks, sorry I did not get back to you before.

I sent an email a few minutes before.

Regards

Ufopolitics 

[Ufopolitics]

WARNING: THIS DIAGRAM HERE IS WRONG, RELATED TO POWER SUPPLY TO BOARDS, PLEASE SEE  FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED - Page 61 (overunitymachines.com) FOR CORRECTED DIAGRAM.

Hello Dear Kampen,

According to the Diagrams that you've sent me, about the internal connections of the V2 Driver, I decided to make a Full Diagram, also including the Coils connections.

Of course, this is for a Two Module only.

Please Right Click on Image and Select "Open Image in a new Tab", so you can see it in its full size (1600 X 832).

Can you verify that the Connections of the 12V Supply to ALL boards are correct?

As I understand the Logic Board supply its 12V Positive and Negative to the two P & NFET Boards.

All the rest is perfectly understood...as Input from Logic Board from 1 to 8 for P & N FET's, and Output Sequence to Coils, that I also did so we all see "The Full Picture"

Regards Friend and thanks again for all your work and your team.

Ufopolitics

[Ufopolitics]

Hello  again,

The Connections to all coils are based on my previous post:  FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED - Page 56 (overunitymachines.com)

And the image is:

Plus, I would like to add, that this Two Module setup, does NOT need to be built on an "Elliptical Core" but also on a TOROIDAL CORE.

Regards

Ufopolitics

[Ufopolitics]

WARNING: THIS DIAGRAM HERE IS WRONG, RELATED TO POWER SUPPLY TO BOARDS, PLEASE SEE  FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED - Page 61 (overunitymachines.com) FOR CORRECTED DIAGRAM.

Hello again,

Ok, so I redid the Diagram, just because I wanted the connections to COILS to look cleaner, besides, I also did it -this time- according to previous image coil connections on previous post (Elliptical Core)

Please to see IMAGE FULL SIZE (1600 X 832), right click on image and select "Open in a new tab" option.

And what I did different from previous Diagram, is just to REVERSE the Coils Sequence, upper and lower, but still having the Blue Exciter coils (North Repulsion) with the Positive Switching.

The point here is that one set must always run opposite, compared with the other.

The Positive switching is the way that Figuera started the sequence, and the way I have disclosed METHOD 2 that I have tested and shown on videos, of just One (1) Module of Exciter's Coils set.

So, on this Dual way, all we need to do is to REPLICATE A SECOND Module 1, EXCEPT the Two Fields, so, it is just SEVEN Exciter Coils connected in series, exactly the same way Module 1 is connected.

And then close loop with Module 1 Fields other terminals, which we normally connected to Negative.

And this Module 2 would be running on Negative switching from the N-FET Board...so, instead of running North Repulsion pole, as you have seen before with Positive, it will be running a South on Repulsion.

But the best part of this New Method of Dual Switching, is that our Fields would KEEP THEIR PRESSURES DURING DISPLACEMENT ALL THE TIME!!

Just because the Inductance, Resistance will maintain EQUALLY DISTRIBUTED between the Two Groups.

Regards

Ufopolitics

[kampen]

Correction:
The three 12V Power Supplies must be three (3) independent Power Supplies
And the minus (---) of the LOGIC board goes to the left side of the FET boards.
So the
12v Opto Nfet is a Power Supply
12v Opto Pfet is a Power Supply
12v Logic is a Power Supply
Xx High is a Power Supply
These four (4) Power Supplies may therefore NOT be connected to each other.

Greetings, Alex