FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello to All,

It has been a long day...testing and drawing CAD's...First, I had a Test planned with the same four coils as it was the Halfway Test, but, I wanted to try using a full cycle...and Diodes Parallel connections, same as prior halfway.

It should work fine right? So, I did first the Diagram, because I planned to use also Four more Coils as feeders for the Four Coils as Exciters...

Image below:

Well, all hopes plus thoughts was that it would work just fine...I was not adding any additional four coils...so Input Amperage should even be lower than half test...

But NO, IT DID NOT WORK, after hooking everything...Amps ramp up SkyHigh again!!

And I already had the setup wires running from commutator as double soldered for the crossing pattern...then I started testing another pattern, which uses similar approach...except that it is an Asymmetrical Pattern.

After hours testing, I finally came up with a way to pulse coils which was very promising...here is the video...tomorrow I am on a work call, so, maybe later on the day or Saturday I will show a specific Diagram for this type of Asymmetrical Pattern...plus another test run.

Here is a fast video I took, just for you to take a look at its response, so far I like it better than sequential testing's...

And please, don't take me wrong, I am NOT planning to disregard ANY of ALL the PREVIOUS tests that I have Conducted so far...as I consider each different Test configuration is Designed to fit different Systems and parameters..

EDIT 1: I forgot to say that what I find on these type of pulsing is a more DENSE ENERGY GENERATION, and you can tell easily, because at very, extremely low pulsing, the bulb does NOT starts to do the blinking, while dimming, like it did on previous pulses configurations.

Regards

Ufopolitics

[citfta]

WOW!  A very interesting video.  I am going to have to watch it a couple of more times to get it all.  But the results are looking great! 

I am wondering why you are using a solid iron core instead of a laminated or a ferrite core?  Won't you have problems in a continual run with heating of the core from eddy currents?

Great video.

Regards,
Carroll

[Greg GKP]

cleaned

[blackchisel97]

WOW!  A very interesting video.  I am going to have to watch it a couple of more times to get it all.  But the results are looking great! 

I am wondering why you are using a solid iron core instead of a laminated or a ferrite core?  Won't you have problems in a continual run with heating of the core from eddy currents?

Great video.

Regards,
Carroll

Hi Carroll,

Ferrite core may not perform well at such low frequencies but laminated core may be worth trying.

V

[Ufopolitics]

ANY MAGNETIC FIELD INTERNAL AND SPATIAL BLOCH WALL

Hello to All,

On the following posts, I will be making a Deeper Analysis* of this New Exciters Asymmetrical Pulses...that will include Lab Testing and all possibilities to expand this method.

* I am sure, for some, it would be a learning experience that you did not learn about Magnetic Fields on School...

Unless you have read Ken Wheeler's book, by now, or have seen all my research on Magnetic Fields Videos...

Ok, first I will start by the simple fact that ALL Magnetic Fields (ALL, including Permanent Magnets and Electromagnets, which includes Solenoids, Generators, Motors, Induction Coils, etc,etc)

All Magnetic Fields have, what some may know by "Bloch Wall", thanks to Scientist Felix Bloch, who discovered a while ago...

Ken Wheeler calls them "Dielectric Field" and "Counter Spatial Plane...as He considers that is the plane/field, from where Fields merge and return.

This is no fiction, anyone could see this exactly center dividing line clearly with Magnetic Viewing Film...or a Ferrocell, Patented by my friend Tim Vanderelli...

Or a Cathode Ray Tube (CRT)...

Anyways, deeper info about this is out there, including the read on free e-book on this site, by Ken Wheeler.

Point is, that whenever you turn ON a Coil...at is DEAD CENTER, exists this Bloch Plane...AND, as soon as you turn it OFF it "goes away"...along with the Magnetic Field.

Second, whenever you turn ON, TWO Coils in Proximity of its Spatial Magnetic Field, IN ATTRACTION, but not touching each other's, or with a Spatial Gap in between...it "forms" a THIRD SPATIAL Bloch Plane, exactly in between Both Fields...Yes, in the air.

So, I want you to visualize all this, with following image:

So, every time you turn ON that switch, Bloch Planes are originated as shown by a Green Line on image.

1- We have all Coils having a Center dividing green line, PLUS...

2-The Spatial Bloch Planes originated in between each Coil IN AN ATTRACTION CHAIN ONLY during the TIME THEY ARE ON.

3-And more IMPORTANT to know here is, that the FURTHER AWAY that each Coils is...or the bigger that Spatial Gap be...it starts to "weaken" this SPATIALLY Bloch Plane.

Until, if Fields keep separating, it disappears/vanishes completely.

Of course, some commonsense here, it also depends on the STRENGTH of the Field...in order to weaken only at certain distances.

Now comes the "details" when we start complicating the "switching scenarios"...

Whenever you -in a very short period of time- Turn ON and then OFF and then turn ON another Coil which is either closer or further away from another one still ON...within its Spatial proximity...these Bloch Planes tends to travel in space to the newly formed one...and I will explain this further on, when we go to the specifics on Asymmetric Pulses for our Exciter's Systems.

To be continued...

Ufopolitics