FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

FIELD PROPAGATION TEST ON 3D

Hello All,

Ok, on previous page, on Post #352 :  FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED - Page 71 (overunitymachines.com)

I showed the Tests to be done with Gauss/Tesla Meter however, it was on a 2D Graphic:

And since I already have the MAYA 3D Scene created of this Linear-Series setup, I wanted to show on full color and on three dimensions the exact points where we need to set our Meter Probe end Sensor (shown with numbers matching above image):

FIRST, THE SEQUENTIAL EIGHT COILS SET AT DEAD CENTER OF STEEL CORE:

On above Image the #1 Red Reading should show a STRONG South Pole measurement, while measurement #2 should be LOWER in Strength.
The #3 Reading should be a weaker N Pole than if we take a closer to N-Pole right on coils end (not shown) but similar to #1 South reading.
And so, #4 North reading should be a MUCH WEAKER reading than #3...
And I am referring to FIELD STRENGTH.


AS SECOND, WHEN WE MOVE ALL EIGHT COILS TO THE LEFT OF SETUP:

On above image, when ALL Eight coils have moved to extreme LEFT of Center Steel Core...We should have a DOWN GRADIENT READING of FIELD STRENGTH from Points #1 (VERY STRONG), to Point#4 ( VERY WEAK)
As the Opposite should take place with Point#5 (Blue North) which should be a VERY STRONG FIELD READING, first because the Pole Proximity, and second because the Amplification due to the Steel Clamp Brackets.

Now, on ALL these Tests, we are looking for A WEAKER READING of Field Strength, as we move Meter Probe FURTHER AWAY from the Eight Coils END POLES,

ALL Eight Coils are SERIES CONNECTED and being POWERED by a 50V/1A Power Supply...realizing we have a TOTAL of 50 Ohms Resistance at BOTH END COIL'S TERMINALS.

Regards

Ufopolitics

[Ufopolitics]

Dear Ufopolitics,

I am amazed every day by the work and the presentation that You do.
I always appreciate the unique perspective you bring to us.
Thank You for always putting in Your best effort at work.
Keep up the good work.

Greetings, Alex

Thanks much for those words Dear Alex!!

And THANK YOU for Designing and Building these great Solid-State Drivers, which will lift our development to SKY HIGH LEVELS and "State of the Art" work to displace our Virtual Field Spatially and never seen before!!

Regards Friend

Ufopolitics

[Ufopolitics]

VERTICALLY STACKED CENTER LAMINATED STEEL CORE

Hello All,

Ok, as I have previously described -IN DETAIL- on Page 70:

FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED - Page 70 (overunitymachines.com)

It is about another Test I want to conduct with the same Coil's Arrangement, where only thing changing is the Center Steel Core:

And I have it also on 3D CAD Drawings for a better understanding:

And ALL I am changing here is the Center Steel Core type of Laminations.

Construction is based on several vertical plates of 1 1/2 X 1 1/2 inch (38X38 mm) compressed by two END STEEL PLATES and One or Two Crossing long Bolts, or simply a threaded rod.

Then both End Plates would have Four holes on the same place of the Steel C-Clamps Brackets, to attach all the assembly together.

Now, the Two End Steel Cores for the Second Secondaries, the laminations would be HORIZONTAL, for easier Field Propagation to these two secondary coils, whenever Sequenced Virtual Field is reaching any of the two extremes:

To then compare Testing results versus the Full Horizontally Stacked Lamination Set.

Regards

Ufopolitics

[Ufopolitics]

Hello to All,

Ok, here is a short video of an update on my Linear Series Laminated Steel Core:

On video I said that previously each Sequential Coil width was "1 and 3/4 Inch" and that is wrong ...before, each sequential Coil was 3/4 Inch (0.75") which is 19 mm width
And now each sequential coil is 0.61 inch which is around 15.5 mm and I round it up to just 15mm.
So, as you can notice, the difference in coil width is just about 3-4 mm...

Here are some images of the build.

Later on, I will show the CAD Diagrams of this new measurements spec's that I am building it now, due to the error I made on total length.

Regards

Ufopolitics
 

[Ufopolitics]

Hello All,

Ok, like I wrote before, here are the new measurements I have now, due to my cutting Total Length error.

And I have on same CAD both measurements, the old and new one, so we could compare both on same image:

Now, the disadvantages that I have here, relates to the Main Center Secondary Coil and relationship between Sequential Ring Coils and Core Center.

Because by having less length at center core member, then the Secondary Coil HEIGHT, would be greater than on a LONGER sized core (considering using the same wire length for both examples)

And this fact sets all the sequential coils "a bit" further away from the steel CENTER core than a "flatter" (lower height) secondary coil would do.

These generators design requires that Sequential RING Coils to be as close as possible to the Steel Core CENTER (and this applies to ALL Methods, no matter if Toroidal, Elliptical, Dual or Quad or more Modules)

So, the "lower" the height of the Center Secondary Coil, the better.

That is the reason why, I've decided to elongate the Core Height, from 1 1/2 X 1 1/2 inch (square) to a more rectangular shape (1 1/2 X 2 inches)

This way I could fit better the 16 gauge wire length and get as close as possible to 4.0 Ohms.

And here I will expand on further posts, about the best geometries for Steel Cores CROSS SECTION...so, we do not have to make generator that long, basically on center member, where Sequential Coils are set.

Simply, we will eventually need to leave behind the "Round and Square" Core Designs, to move towards a more Rectangular cross section geometry.

And it does not matter if rectangular cross section is set Horizontal or Vertical.

The Rectangular Pattern offers Two Advantages over Square and Round:

1- The Center Secondary Coil -using thick gauge, (like 12, 14, 16)- will expand into longer loops, allowing larger number of Length/Turns.

2- On a Rectangle Pattern, there will always be Two sides where it will always be very close to the center of core.

As this will also reflect on the Sequential Ring Coils proximity to the center.

I will keep expanding into this -very important- development on further posts, with the appropriate CAD Images.

Regards

Ufopolitics