How to build a Permanent Magnetic Shielding device applied to a workable motor

[Dr.Wlazlak]

One of the main problems of using Permanent magnets is They can not be turned OFF
If a device could produce an effect of blocking the magnetic fields of the magnetic poles to each
other ( and the blocking device was not effected by the magnetic pull or pushing effects )
The blocking device could be placed between to poles of the same magnetic fields
like North pushing against North ( And the blocking device would allow the 2 magnets not to
be able to push against each other and could moving together close -- once the blocking device is
removed from between the 2 magnets ( they push apart ) making usable output energy
Note: many different type of devices can be built using this magnetic Shield technology
( Because the blocking device is NOT effected by the magnetic force of the 2 magnets )
NO energy is taken away from the total of the usable output energy - other than linkage friction -

This method has been tested and it does work - no motor device have ever been built using this
method of magnetic shielding - But it does work as a shielding system producing no back pulls - as the device
is remove from between the 2 magnetic of the same poles ( as shown )





Something to think about or Test for yourself
tested in 2011 -- a few years old technology

[Ufopolitics]

Hello Dr Wlazlak,

Unfortunately, at this point I do not have all the time to seat down -to go in detail- to respond as to make the required CAD Graphics related to your post setup.
I am going through critical health issues in my family (not me)
My wife is in the Hospital being treated on an aggressive type of cancer (adenocarcinoma on the lymph nodes).

However, on this brief post, I will try to express my main point of view(s):

One of the main problems of using Permanent magnets is They can not be turned OFF

That is correct, however, as you have shown, there are other ways to do so, 'indirectly'

You have shown the image below:

And yes, on first image there are two North Poles on Repulsion...as on the lower image when you insert that Iron/Steel Plate in between, then another Magnetic Bond is formed:

[N>>IRON PLATE<<N]

And of course, the previous repulsion forces pushing apart in 180-degree vectors are gone, or at least diminished in great degree*...

*In order for these two forces to completely disappear, the new bond of two norths with iron plate have to be able to completely absorb these forces, meaning, be equal or greater than...based on the type of force the two magnets have versus the iron mass VOLUME, as also the 'GAP' between magnets-plate on the setup.

However, to REMOVE that Iron Plate from that newly formed Bond [N>>IRON PLATE<<N] will take also considerable force to pull it apart.

The question here is simple, if you sum up the two previous Repulse forces at 180 deg and compare it to required force to pull away the plate from the new bond...what would the result be?
Have you done this analysis?

Now the last Image:

That is a very interesting way to put this technology in use...again, unfortunately at this moment I do not have the time to go over in detail.


Regards

Ufopolitics

[citfta]

This video might be interesting to you.  I did it a few years ago.

https://www.youtube.com/watch?v=68ChN24x_HU

Carroll

[Dr.Wlazlak]

Hello Carroll - Nice Video - The concept I have shown above a similar to what you demo in your video
One drawing I did not show in this was - The drawing below - 


What is shown here is in Fig. 3 having North and South next to each other in the way shown 
The magnet to the left of them is in balance to the push and pull force equal
in fig. 4 the same thing applies using a steel plate to attach the North and South magnetic to
in Fig. 5 below there are magnets placed on both sides of the steel plate 
The North / South on each side produce no attraction to the 2 south facing magnets on either side
( This Shield produces no Pulls or pushing effect ( to the 2 outside south magnets on either side )
if set correct 

Notice: The force of magnetic energy still is present but is directed DOWN at 90 degrees to the 
2 south magnets to produce the energy output 
( having the shield being able to pull horz. out having NO back or forward force of magnetic attraction allows a motor type device to be built of usable energy output )
The Shield using very little of the output energy to Block the magnetic pushing effects allowing the return to a close point Where the (south to south can push apart again and again )

Fig. 6 shows the horz. pulling out of the shield ( Like said There is no pull or pushing using this balance shielding device 
The force is being redirected (Down) using bearing to roll on make it very easy to move
Of course there could be another method using Electromagnetic forces in a shield device
allowing the shield to push away freely using very little of the output energy to do so
like a no load motor the uses very little energy to move 
a steel plate could be turn opposite of attraction and push out from being the shield between 
As shown in a simple idea below

There are many way of making this type of system into a motor type design 
Where the steel shield that would normally produce the same attraction backward 
can by using this method be part of the output and running on Permanent Magnetic force as the main output of energy produced

Fun Stuff - some many options - There must be thousands of ways of making workable devices -
I have it least 20 or 30 ways myself

[Dr.Wlazlak]

The Electrical shielding system is a interesting idea because using this method the electrical input also becomes a motor type output system and the Permanent Magnetic force is the main power source added
to the electrical motor working as a shield at the same time 
A simple design shows one possible method of doing this in a rotary motion using gearing to tie system together and also used as the timing for the system
The first drawing shows the gears sizes and how they would be arranged 

The next drawing shows the line up of the shield to block the magnetic field from each other

The next drawing shows the magnetic wheel having a 10 deg more turn and opening the shield
to allow the magnets to push to rotary action 

The shield is built like an electrical DC. motor where the switching always keep the poles on one only
Note: this on the drawing below


This is one method of producing a workable output system using Permanent Magnetic Potential Energy as the main power source and using electrical power input as a second power source in Unity 
Note the main wheel turn 1/3 the speed of the shielding system where the shield is also a motor output system running at 3 times the speed of the main magnetic wheels 
The electrical input power only needs to be 1 /10 th the total output power of the device to produce this effect 
Again - Fun Stuff - Dr. Wlazlak