FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[kampen]

Subject: High Voltage Suppression and Next Steps

Hello Ufopolitics,
Many thanks for your detailed follow-up and clarification.
I fully agree that the HV suppression setup is clearly fulfilling its primary role in protecting the switching electronics.
While the reversed voltage spikes indeed appear at higher-than-input levels,
I also observe that their actual energy content is minimal due to the very low current associated with them.
Your experience confirms this and makes perfect sense.
As you rightly mentioned, reusing such voltage peaks would require proper transformation and conditioning to bring them into a usable power range, which is 
not essential at this stage.
So for now, their role as protective dampers remains the key role.

With that protection in place and working effectively, I am now preparing to proceed with raising the input to the sequential coil banks.
This will be done carefully, step-by-step.
Next, Input 12 V – 24 V, then 36 V, while monitoring coil temperatures, check spike suppression behavior, and waveform symmetry across the sequence.

I will keep you updated with the next test results as I explore the higher Input Voltage levels and check how the system responds.

Thanks again for your ongoing support and insights, which are always appreciated.

[Ufopolitics]

Hello to All,

As my friend Kampen is still waiting on back order diodes to finish his tests...I want to review the setup that Pierre Cotnoit had...

And even though his setup is not the same as the Linear Figuera, it stills have a lot of components parts of his system that we coud study closely...

Like the Coils Return Energy we could reuse.

Pierre Cotnoir DZ  Generator was very different setup -on Electro-Magnetic Energy Structure- from what we have on a Linear Figuera, so, he was reversing every 180º , 36 Coils that were N-S to S.N...generating a "Simulation" of a Virtual Rotation of all 36 Coils at exterior of the Motor Casing.

Then he needed twice the number of diodes to perform his task...and of Relays, also were needed twice, meaning 72 relays and 72 Diodes.

Simply, Pierre was REVERSING his total of 36 Coils at 180º....on a given Cycle, to simulate a Field Rotation.

However, the must important part, are the diodes recovery system, sending its energy back to his Ultracap Bank of 24 Volts.

Regards

Ufopolitics

[Ufopolitics]

Hello again,

Below I am quoting myself from my previous post, on the part I care about analyzing here:

...Simply, Pierre was REVERSING his total of 36 Coils at 180º....on a given Cycle, to simulate a Field Rotation.

However, the must important part, are the diodes recovery system, sending its energy back to his Ultracap Bank of 24 Volts.

Regards

Ufopolitics

And -of course- this energy returned from all 36 coils will just be a MINIMAL amount, compared to the requirement that a bank of 18 Ultra Capacitors demand.

That is simply the reason why, Pierre rebuilt a transformer (seen on the left of image)

For all of you that may not know, Supercapacitors, or Ultra Caps require  HIGH AMOUNT OF AMPERAGE* ( * Amperage Levels Depends of total capacitance of bank, however, even to charge One Cap based on 3.0V it will take easy from 5 to 8 Amps on the Startup) in order to start charging.

So, this Transformer uses an Input of around 115V/0.5 to 1.0 Amps and delivers 24 Volts with much higher amperage. Reason why he used a thicker (coarser) wire on the trafo secondary.

The purpose of the Ultra Cap Bank, is just to keep feeding the Low Voltage/ Low Amperage Electronic circuit enough time to 'disconnect' transformer from external AC Source and plug it to the Secondary of Generator AC Outlets, to CLOSE THE LOOP....And that's ALL.

After the Generator Output keeps running transformer, then the caps are just a storage bank (once fully charged)...as it also serves as a "Filtering Power Source" for protection of Low Voltage electronic components (Arduino Processor).

On my opinion, this whole system has many flaws, and it 'barely' made OU by a few Volts/Amps...

I will cite the BASIC flaws below:

1- This Rotary System have many electromagnetic losses, due that Inner Secondary NOT COVERING a FULL 360º of the Outer Rotational Coils, and only at certain angle it gets a FULL INDUCTION.
2- Relays are very unstable for this job, which they are not designed for, they either stay OPEN or CLOSED for a long time, NOT for continuous ON-OFF´s. So, they are very slow responsive for this task, after a while of operation. That´s why they burnt up for his expected second test, that never took place.
3- AND MORE IMPORTANT, Everytime we reverse the DC INPUT of ANY COIL, We are simply KILLING the Magnetic Field and restarting a new one. This causes the previous Currents feeding the previous Field to also REVERSE.
And basically we do NOT have a SMOOTH  Magnetic Field transition that simulates a displacement through Spacetime, no matter if it is Rotational or Linearly done...we are just driving the magnetic fields based on CONSTANT REVERSED SPIKES.
I have written about this "NO, NO's" whenever building an OU Machine back on my first posts on this same Topic...DO NOT REVERSE FIELDS!!
I was doing it and failing over and over.
Basically, if you go to ANY ROTARY AC Generator out there, ANY...you will find out that their DC Exciting Fields NEVER get reversed on DC Polarity, or Fields Magnetic Polarities...they are always CONSTANT, same Field Strength Values, driven by the same voltage and currents at ALL TIMES !!

*********************************************

REGARDLESS and HOWEVER, Pierre Cotnoir´s design on recovery from diodes, plus the Transformer that he built, plus the Ultra Cap Bank is -in my opinion- very well put together.

Let´s remember that on his setup, he reverses the DC input of ALL 36 coils...And this also makes his return much WEAKER, LOWER in Reversed Voltages.

However, on the LINEAR FIGUERA that I have designed we do NOT reverse Coils at ALL.

We are just DISCONNECTING a Linear Series of Connected line of Coils (COIL CHAIN)...AND THIS FACT, generates MUCH MORE REVERSED VOLTAGE POWER than Pierre´s DZ Generator.

I believe, at the end, on our setup, we will eventually need a Transformer...that helps STABILIZE these Much Higher Reversed Voltages with LOW Amperage and converted to our FINAL DECIDED INPUT would be, say, 36, 48 or 100 Volts of DC Input to our Sequential Coils. However, it would still needs a steady Input from Generator.

We still need a LOT of Output Testing to do, as how much our TWO END Second Secondaries generate with our setup running at full operating speed (Frequency) AND LOADED.

Because, IF our Two End Coils F1 & F2, (Second Secondaries) Generate enough to fullfil our Input, then we will NOT NEED a Transformer...the system will "Auto Self Loop" only from these Two Coils connected in series and ran through a rectifier bridge and small cap...Just like a typical Home Generator does, with their Exciter Static feeding Coils within the Generator Stator Frame-Core.

These Two End Coils would do the job of Pierre Cotnoir's Transformer...as we could add aldo whatever we recover from Coil's Reversed Voltage...

Regards

Ufopolitics

[kampen]

@ Ufopolitics,

Excellent analysis. I completely agree with your breakdown. 
The recovered energy from the 36 coils would indeed be minimal relative to what's required to charge an ultracap bank of that size. 
Even if every collapse pulse were captured perfectly, the available joules just wouldn't meet the cap's initial charging demand, 
especially considering the 5–8 A surge you mentioned for 3 V per cell.

Your point about the transformer addition makes perfect sense. 
Pierre clearly needed a low-voltage, high-current supply to bring the cap bank up quickly and provide the "bridge" during the brief transfer phase before switching to the generator's own output. 
In that role, the ultracaps act more like a buffer/filter than a source of sustainable drive energy.

The flaws you listed are spot on:
Partial induction coverage — losing coupling angle means intermittent energy transfer, not continuous induction.
Relay switching limits — mechanical relays simply can not handle the high-frequency polarity reversals without lag or contact degradation. 
Solid-state switching would be required for any stable operation.
Reversing DC coil polarity — that's a critical insight. Each reversal completely destroys the existing magnetic field, 
wasting stored energy in heating and reverse current surges. 
Real rotating machines, as you said, never reverse their excitation; they maintain constant polarity and create motion by spatial displacement of the field, not by flipping it.

In that sense, Pierre's approach was more of a magnetic pulsing experiment than a true analog of a rotating generator. 
It is clever, but it can not replicate the smooth-moving field that is necessary for continuous induction and energy transfer.
Your explanation ties it all together beautifully: the system likely appeared to edge into OU territory because of transient overlaps and stored charge behavior, not because it achieved sustained gain.

Thanks for taking the time to clarify those deeper design points. 
This really helps separate and sort out what is conceptually interesting from what is physically viable.

[Ufopolitics]

[...]


So, on image above I have cleaned up all previous secondary circuits plus test points, leaving only the 13 Sequential Coils and their connection with the N & P FET Boards.

And here I will go, step by step, on how the sequential order works starting on #1 terminals (positive and negative at unison, same time)
1- When BOTH #1 Terminals activate ON, at both boards (-/+) then Coils B1, B2, B3, B4, B5, B6 & C Turn ON, while R1, R2, R3, R4, R5, R6 are OFF, this is Group # 1 ON (Extreme Left Field Location)
2- When BOTH #2 Terminals activate ON, at both boards (-/+) then Coils B2, B3, B4, B5, B6, C & R1 Turn ON, while B1, R2, R3, R4, R5, R6 are OFF, this is Group # 2 ON
3- When BOTH #3 Terminals activate ON, at both boards (-/+) Then Coils B3, B4, B5, B6, C, R1 & R2 Turn ON, while B1, B2, R3, R4, R5, R6 are OFF, this is Group # 3 ON
4- When BOTH #4 Terminals activate ON, at both boards (-/+) Then Coils B4, B5, B6, C, R1, R2 & R3 Turn ON, while B1, B2, B3, R4, R5, R6 are OFF, this is Group # 4 ON (Center Field Location)
5- When BOTH #5 Terminals activate ON, at both boards (-/+) Then Coils B5, B6, C, R1, R2, R3 & R4 Turn ON, while B1, B2, B3, B4, R5, R6 are OFF, this is Group # 5 ON
6- When BOTH #6 Terminals activate ON, at both boards (-/+) Then Coils B6, C, R1, R2, R3, R4 & R5 Turn ON, while B1, B2, B3, B4, B5, R6 are OFF, this is Group # 6 ON
7- When BOTH #7 Terminals activate ON, at both boards (-/+) Then Coils C, R1, R2, R3, R4, R5 & R6  Turn ON, while B1, B2, B3, B4, B5, B6 are OFF, this is Group # 7 ON (Extreme Right Field Location)
As above I have written all #1 to #7 Sequences, which includes that Magnetic Field has traveled from the extreme LEFT (#1) passing through CENTER (#4) until it reaches #7 or the extreme RIGHT.
Also to realiza that on ALL SEQUENCES, Coil C is always ON, Meaning that we can use this Center Coil in order to Regulate the TOTAL Resistance of the Field, no matter where the Field Spacetime Positioning is.
And, as you all know, by Lenz Law, increasing Resistance will lower our Operating Currents (Amps) while keeping the same Voltage V.
Also, when testing, make sure Coil C is checked for temperature increasing, this is very important!!
Regards
Ufopolitics
Post Data: As it is understood the Sequence shown and explained above ONLY travels from #1 to #7 Terminals, and this is just 1/2 Cycle, meaning, that once it reaches #7, then the Sequence starts 'going backwards' or from #7 to #1, these completes a FULL Cycle.

Hello All,

Previously on post # 387 (see full post here)>> : https://overunitymachines.com/index.php/topic,5.msg2648.html#msg2648

On above quoted post, I have explained the sequences from 1 tto 7, However, it was Related to GROUPS...

So, I made the below Diagram, so a full context is understood, I made it simpler, as I am not including Letters/Numbers for each coil, so it is only ABOUT GROUPS, from G1 to G7:

As the objective is to show a Test that should be conducted, before starting the System Sequences.

And that is to measure independently the Resistance of each Group, of course, it just need to be done once, from G1 to G7, HOWEVER, the connections to FET's must be removed, not to get any false resistance readings.

So, on the case of Kampen 13 Coils, he has each sequential coil approximately at 6.0 Ohms each. (more or less, we do not need to be that accurate here)

Each Group have Seven (7) Coils, so the Total Resistance should be near the 42.0 Ohms.

On the Diagram [G1-R1] means Group One (1) have a Resistance R1...And it would be to set a Resistance Meter between both same number terminals (#-1 & #+1)

And at the end, ALL RESISTANCES for each Group MUST BE AROUND THE SAME Resistance Value...

Or the "IDEAL" goal is that : R1=R2=R3=R4=R5=R6=R7= 42.0 +/- Ohms

To be more precise, we could measure first each coil resistance to see if all are around the 6.0 Ohmsvalue...it don't matter if one is 6.25 while the other is 6.10...

Once the System starts warming up, plus reaching the running frequency, it will start a process of "equalization"...

But, this test will make sure we do not have any wrong connections...eg: by having one group with six (6) coils and next with seven...this will show on the TOTAL RESISTANCE between them.

As if ALL RESISTANCES PER EACH GROUP are around the same value, this will guarantee we will have the SAME AMPERAGE, HENCE THE SAME FIELD STRENGTH during the Sequencing.

Regards

Ufopolitics