FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello to All,

Ok, Unfortunately, I've got some emails from some Builder's here that they cannot "grasp" (understand) quite well this new Toroidal Design approach...

So, I have decided to go back to my Post#207, on Page 42...to start "from scratch" from that point in time.

First, I will quote myself on that post (so you do not have to go back to read it):

DETAILED ANALYSIS ON SEQUENTIAL FIELDS POLARIZATION

Hello to All,

At some point, I had in mind to make this post...now I have the time.
As I consider this Post, the MOST IMPORTANT POST OF THIS WHOLE TOPIC/THREAD, since the following Analysis describes exactly what are the MAGNETIC INTERACTIONS between ALL Sequential Coils related to Both Field Stators.
And if you just set one connection reversed, or not on the right place...or set a coil reversed, the whole System will NOT perform as expected. or may collapse. Just like in a very accurate electronic board connections.
On this image below, I have tried to best represent every single connection, as every single polarity, exactly as it takes place on the Real Setup:

First, it is mainly based on representing the Positive Input from the moving brush on the rotary system to the TWO COILS receiving this positive charge.

As you can see, when positive input enters circuit, it DIVIDES/SPLIT to Right and Left of point of entry, on this position it enters through Contact #5 and it initially Turns ON Coils #4 & #5.

HOWEVER, please note that Positive enters to START of Coil #4 while on Coil #5 it enters through Coil END.

This difference of terminals positive input generates TWO OPPOSITE POLES to be FACING EACH OTHER'S, OR A REPULSION, BUT ONLY ON THIS SPOT!!

That is the reason why I have ENCIRCLED this specific REPULSION INTERACTION.

NOW, from that CENTER REPULSION CIRCLE-POINT, to the Right and to the Left, there would be an INVERSED ATTRACTION CHAIN, all the way to meet BOTH Fields, #1 & #2.

NOW, this image only represents a "FRAME" on the SPACETIME DISPLACEMENT of the Sequence...

And you will need to "train" your minds, to mentally MOVE that CIRCLE to the Right and Left...always keeping that repulsion CIRCLE wherever the Positive Entry Point moves, PLUS also keeping BOTH ATTRACTION CHAINS.

As we move Positive Brush-Arrow to Contact #6 (Right) the Right Attraction Chain WILL REDUCE ITS SIZE...while the Left Attraction Chain will EXPAND ITS SIZE.

If we keep moving the Positive Brush all the way to Contact #8, then Left Attraction Chain would be EXPANDED to its MAX RANGE, while Right Attraction Chain would completely disappear, and Coil #7 and Field #2 will be facing on a Repulsion Interaction.

And of course, when Positive Brush returns all the way to Contact #1, the complete opposite function will take place...

Here, for Us, who believe on the Magnetic Field VORTEX CONFIGURATION, or like a "Corkscrew", like Minkowski (Hermann Minkowski, Einstein former Math Teacher) once mentioned on his paper about the "Theory of the Spacetime"...We believe on these types of Interactions like described above, we are not only just "varying the flux"...

But here, we are generating a series of Vortexes, which are opposed to Two, right and left groups, which increases and decreases over spacetime, greatly favoring our Output AC Sine Induced Wave to the Max Levels.

I hope that you all understood this post completely, because it is VERY IMPORTANT that whenever you start putting together your setup...you have all this info on mind.

Regards to All

Ufopolitics

EDIT 1: Please remember that ALL COILS, including BOTH Fields, are wound Counter Clock Wise (CCW) from the START point on FIRST LAYER!!

EDIT 2: Also realize that Both Fields 1 & 2, NEVER CHANGE their Magnetic Polarization.

To be continued...

Ufopolitics 

[Ufopolitics]

Hello,

Ok, so, basically on previous REPOSTED TEXT (quoted post), I have never mentioned the word "Secondaries" or "Secondary", or their alignment at all...as a matter of fact, the "secondaries" on that post are just Blank Rectangles not even showing a connection.

So, please, Secondaries Structure, Shape or Geometry, is NOT IMPORTANT AT ALL for a better and complete understanding of...

JUST THE SEQUENTIAL COILS PLUS THEIR RESPECTIVE FIELDS.

So, I have made a NEW IMAGE ABOUT THIS IMPORTANT POST, where I have NOT INCLUDED ANY SECONDARY COILS AT ALL...IT IS JUST THE PURE AND SIMPLE EXCITER SYSTEM, THE WAY THEY CONNECT ELECTRICALLY, PLUS THEIR MAGNETIC INTERACTIONS:

So I have "compacted" here, this Exciter System Module, strictly ALL Seven (7) Sequential Coils Plus their Respective Fields, 1 & 2. BUT, it is exactly the same EXCITER'S CONFIGURATION as on prior quoted post #207.

This is so far our BEST MODEL, related to ELECTRICAL CONNECTIONS, METHOD OF WINDING COILS, AS MAGNETIC INTERACTIONS, which include:

1- Two (2) Opposed Attraction Chains.
2- One (1) Repulsion Field (here, because it is a Positive Electrical Input, is a North Polarization.
3- Two (2) Fields which are OPPOSING MAGNETICALLY, at their North Polarization (Pole)

Ufopolitics

[Ufopolitics]

Hello again,

Ok, so on this Diagram, I am basically showing what I have done, to come up with the New Toroidal Geometry of Figuera...Let's call it  FTPU in short, as Figuera Toroidal Power Unit.

Basically, I got TWO FULL POSITIVE SWITCHING SINGLE MODULES (exactly like seen on previous post), and Incorporate/Insert them into the Toroidal or Closed Structure, as Image shows...One FACING the other One, EXACTLY AT 180 Degrees Apart.

And of course, when I said "FULL MODULES" I meant including their TWO RELATED FIELDS.

Plus, in order not to create confusion, I am not showing here the Negative Switching Coils that would complete the CLOSED TOROIDAL STRUCTURE.

Hope so far, all this Posts and Diagrams would help to better understanding this new system.

Regards

Ufopolitics

[Ufopolitics]

Hello again,

Ok, now I would like to ask...based on previous single module of Positive Switching, that it looked like below:

What would happen if I just REVERSE ELECTRICAL POLARITY?

Like, instead of Switching Positive Input, I would rather Input and Switch Negative through ALL Sequential Contacts...as Input Positive to BOTH END FIELDS?




Mmmm...let's see it:

So, like I wrote before...by just switching the Electrical Input (+/-) and LEAVING THE SAME WAY ALL COILS WERE SHOWN BEFORE, Method of Winding (CCW)...AND ALL ELECTRICAL CONNECTIONS...

We see what happened right?

ALL the MAGNETIC POLARIZATIONS GOT REVERSED.

And so, instead of a North Repulsion Pole...we get a South Repulsion...plus ALL ATTRACT CHAINS reversed their polarity...HOWEVER, they are still on ATTRACTION MODE.

Now, please look at BOTH FIELDS, 1 & 2...and compare them with Positive Input Image above.

They have also reversed their magnetic polarity. Now, both Fields are FACING towards center a SOUTH POLARITY...

Now, my last question...

Would this reversed electrical polarity generator work, with Negative Switching same way as with Positive Switching and Negative to Fields?

Absolutely it will work as well as Positive Switching...same thing, different magnetic Polarization, that's all.

Now let's get back to the Closed Structure again...next

Ufopolitics

[Ufopolitics]

Hello,

Ok, Final Chapter on the ASSEMBLY of the FTPU...

Now we just need to Insert the Negative Switching Modules...to complete the full Closed Structure (Toroid here)

So here is that image with ALL Four Modules around Toroid:

Ok, so, above I have set the FTPU at center like the Fig3 previously shown, plus all Modules that were attached.

And here, with the Negative Switching Modules there is a "slight" difference...compared to the Positive Switching Modules.

Prior we assembled the FULL Positive Switching Modules, and that included the Two Fields that were set to both Modules.

However, if we compare Pos. FIELDS Magnetic Polarity Orientation, with the Negative Polarity Modules FIELDS...we realize they are IDENTICAL POSITIONING/ALIGNMENT related to MAGNETIC ORIENTATION and ELECTRICAL POLARIZATION INPUT.

So, we do NOT need to "reuse" these Four Fields from the Two Negative Switchers...and just Use the Fields from the Positive Switchers to be COMMON TO ALL.

And on below Diagram, I deleted their Fields...just leaving the Sequential Negative Switching Coils:

Then, ALL we need are the SEQUENTIAL COILS that switch Negative, to be inserted on the Assembly...and it will align beautifully!!

That is why on the Graphic, I have separated the Switching Coils from their FIELDS...because we will not be using them, just the Two Negative Sequential Coils.

Then we have a FULL CLOSED TOROIDAL STRUCTURE, where only Four Fields are needed to complete the sequencing...

And that's all folks

Regards

Ufopolitics

Edit Add 1:Please realize that now the Negative Switchers (Negative Sequential Coils) would be feeding Negative to ALL FOUR FIELDS that Switch Positive...