FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[citfta]

Hi Fessor,

What you are seeing is what the Figuera device is supposed to do.  According to the theory about the device as you put voltage into the coils of one polarity they should induce voltage into the coils of the opposite polarity.  This can only happen if the coils are arranged in the proper oonfiguration.  And after many years of research UFO has finally found that configuration.  I have also tested may different configurations of coils.  And so far the only configuration that I found that works this way is Ufo's configuration of alternating coils.  By inducing voltage into the opposite polarity coils this reduces the input current required to keep the system operating.  Since all scope channels are connected to a common ground the scope is correctly showing that the opposite polarity coils do go below ground when being induced by the acitve polarity coils.  I hope this explanation helps some,

Respectfully,
Carroll

[Fessor]

Hi Carrol,

thanks a lot, but you get me wrong

From day one of this thread I have understood the successive DC-field displacement is creating real AC in the secondary, the whole purpose yes.

What I am questioning is the AV or AC on the DC side, and more specifically if the zero-level is correct leveled across DC probes, or if current is actually reversing (negative voltage) - which if - is the first time I have seen such.

Your last explanation

"Since all scope channels are connected to a common ground the scope is correctly showing that the opposite polarity coils do go below ground when being induced by the acitve polarity coils.  I hope this explanation helps some,"

exactly, the common DC ground DC should however also be the common zero line across probes on DC side - which they seem not - or otherwise current is reversing on DC, which is what I am question.

Again thanks, for taking you time 

[Ufopolitics]

Hello everyone,

Thanks for your comments @Fessor & @citfta,

@Fessor: In order to understand this System, you need to "play it" in your mind at very slow motion...as you can NOT leave behind the magnetic fields generated as well.

Have in mind that we are not collapsing any coils on this Method, however, we are adding and subtracting resistance as the brush moves to the right and left of all the different coils chains or circuits of coils, therefore, also altering their currents.

Points 1 and 8, are the Maximum Peak Levels for both ends (Field 1 & Field 2), However, on the distribution, the balance is: max currents to one side, while the other side have all resistance of other coils, at the same timing, same momentum.
Passing by mid points of both points (1-8) on the right and left of commutator, (think about a Clock, where 12 is 1, 6 is 8, and those mid points are 3 and 9) those are the balancing points of the System, where the distribution (of resistance-currents [I/R]) is somehow evenly disbursed.

When you add max current to a coil, to then, suddenly, take it away, also to a max expression, by adding more resistance, it is a very close scenario to a collapse, without allowing for magnetic field to fully disappear. These fast-acting, opposite operations, brings along similar reactions seen on a coil collapse...and that is a partial and smoother Field "tendency" to a Reversal, also known as "coil reactance".

But you cannot evaluate this whole System as a single coil reaction, but a Group Chain of Coils (connected in series) acting at unison for short periods of time.

Then, besides analyzing electrical components mentioned above, like currents and resistance, you need to visualize the magnetic fields changes, as a 3D volume, generated by those active chains of coils on the sequences.

A better way to "visualize" all this, is to understand that brush positioning DIVIDES the Exciter System in Two Main Groups, to the right and left of the linear configuration.

Then, while one group (A) receives less resistance, hence more currents, the other group (B) receives more resistance and less currents...then as we visualize these two groups, we must understand that group A have a stronger and more expanded Magnetic Field than group B.

Now, the fact that Input Signals go below zero, is not a "misinterpretation" of Scope, it is also due to a Field Inertial Displacement or "Magnetic Inertial Movement"...a "momentum" that after field has developed a fast linear travel, all the sudden it is reduced to a minimal expression, ending up in passing (just a bit) its linear travel end.

The Energy I was able to capture yesterday, after the diodes, it is all due to the "coils reactance" on these partial reversals that I have mentioned before.

The Main Component of this System are the Magnetic Fields, all other "parameters maneuvering" we are doing here, like currents, resistance, inductance, reactance, number of turns of coils, geometrical design and positioning etc,...just work in order to generate THE Magnetic Field, displace it, move it, causing the Induction.

Hope this explanation helps you somehow to understand it better.

Regards

Ufopolitics

[Ufopolitics]

Hello,

Ok, so far the Electrical main parameter that we have been working on, or mainly generating at an increased value over input, is Voltage.

We still need to add a second component here, that I have not FULLY disclosed yet, that would be in charge to increase amperage above input.

I am saying "not FULLY disclosed" because, I have "partially" talked about it on the first part of this Topic.

Voltage increase is obtained based on a Progressively Sequential Actuation over time, of a series of coils in a longitudinal chain along the secondary length...fine, I have done that part so far.

However, amperage does NOT increase that way.

Amperage Increase needs a FAST and RADICAL Magnetic action, (NOT a progressively Sequential one, over time) from one extreme to the other of our Secondary longitudinal range, in the shortest, minimal time.

...a Force adding component, an Impact.

Now, we need to incorporate this Amp Increase Component, in order that it falls/keys, into our "Rhythmical Sequence"...and it must be also in a "duality" (work for both ways of the magnetic displacement) of our System.

I am working on that now, as I write here...

Please be patient...

Regards

Ufopolitics

[Ufopolitics]

Hi Fessor,

What you are seeing is what the Figuera device is supposed to do.  According to the theory about the device as you put voltage into the coils of one polarity they should induce voltage into the coils of the opposite polarity.  This can only happen if the coils are arranged in the proper oonfiguration.  And after many years of research UFO has finally found that configuration.  I have also tested may different configurations of coils.  And so far the only configuration that I found that works this way is Ufo's configuration of alternating coils.  By inducing voltage into the opposite polarity coils this reduces the input current required to keep the system operating.  Since all scope channels are connected to a common ground the scope is correctly showing that the opposite polarity coils do go below ground when being induced by the active polarity coils.  I hope this explanation helps some,

Respectfully,
Carroll

Many thanks Citfta,

Yes, it has been many years of hard work...that finally render the results...and I am very happy (you have no idea how much) to share it with the World!!

Now, related to the ground for the Scope Probes, yes channels 2 & 3 are definitively using the same common ground from Input.

However, please note that the channel 1, yellow, its ground is connected to the other terminal of secondary...not common to Input ground.

As also, channel 4, because of the diode's connection, is blocking input ground, as it captures exactly the same signal if I just do not connect it to ground, like I have shown on my second video yesterday.

Thanks for all your excellent posts and contributions here my friend!!

Regards

Ufopolitics