FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello,

On this video I am connecting some AC Motor loads, to see how the Generator responds...how much Input Amperage it increases when fully speeding and stressing a hand drill tool...

On the Scope we can clearly see that the Output Sine (Yellow), remains above both of the Input Sines (Magenta and Blue)...no matter the stress we set on hand tool, which it runs at 120V /1.2A

Regards

Ufopolitics

[greybeardmike]

Ufopolitics,
On the previous test with the additional field coils added, could you be reaching saturation of the core?  Is there some way to test if the core is saturated?
greybeardmike

[Ufopolitics]

Hello GB Mike,

Ufopolitics,
On the previous test with the additional field coils added, could you be reaching saturation of the core?

Not at all, Saturation on this mass of steel I am using, requires of a very High Frequency plus a very Intense Magnetic Field (over 1 Tesla), in order to Saturate it (Fully Magnetized)

I am barely running on all these tests at 43-45 Hertz...as I explained on video, the Rotary Switch is missing some contacts at higher speeds...it will not let me go above 45 Hertz.

Simply divide your running RPM's by 60 seconds (1 minute), and you will get the hertz you are driving your System on.

Example: yesterday the most I ran the switch was at 2560 RPM's...but let's round it to 2600...and that is exactly 43 Hertz.

This System uses Two LINEARLY Opposed Fields of the same Polarity, or a North facing a North, or a South facing a South...these are Opposite Magnetic Vortexes.

So, here the steel domains are constantly changing in a 180 degrees direction, every time one Field takes over the other Field (in spacetime) .

Therefore, these Fields movements, constantly "cleans up" the possibility of magnetic saturation (full alignment of steel domains) to take place.

Is there some way to test if the core is saturated?
greybeardmike

Of course, just check your steel cores for Magnetic Remanence after you turn off the power switch.

If you have the Polarity detector Pen tool I have shown...read it...or simply approach a fine piece of steel...like a razor blade, and check for magnetization, after you turn off your system.

Saturation of Steel equals to Magnetization of Steel...meaning, that ALL Domains are ALIGNED in a certain direction...and then you will have a permanent or momentarily polarization of your core.

Normally the Steel Plates that I use to hold all coils together...if I leave them loose (no bolts attaching them)...and as soon as I stop magnetic flow, by turning off my INPUT power switch...both Plates- at the same time- fall off...that tells you there is ZERO Saturation on your System...or ZERO Magnetic Remanence.

Hope this clears it up for you, Mike.


Regards

Ufopolitics

[Ufopolitics]

Hello to All,

Next Post I am showing a video to help the full understanding of the Magnetic Fields Movement, taking place on this Method 2 of Interactions.

Regards

Ufopolitics

[Ufopolitics]

Hello,

Ok, here is a video about the basic Understanding of this System:

First than all, you need to realize that ALL these Coils (including Field Coils) does NOT have any Ferromagnetic Material inserted into them at all, they are only made of insulating tape, plus paper and copper wires...
Second, that the Steel Core is completely STATIC during this test...

Therefore, what is moving ALL these Coils, is PURELY the Magnetic Fields that these coils generate EACH, and all these individual Fields are carrying these Copper Wire Mass, back and forth with it, at Low Speeds.

As whenever we increase the Frequency, or MAGNETIC FIELD Traveling Speed, then the Copper Mass of Wires can NO LONGER FOLLOW these much faster movements done by this Massless, Weightless Entity...called Magnetic Field Spectrum.

Then, when ALL these Coils are TIGHT, SECURED, on their Housing and Structures...ONLY THESE MAGNETIC FIELDS ARE the ones MOVING VIRTUALLY THROUGH SPACETIME DISPLACEMENT.

Regards to All

Ufopolitics