FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello to All,

And good morning for those on the Eastern Coast of USA...good afternoon and good evening for others around the globe.

This morning, I am making another Secondary Coil, with 20 gauge...and I am doing it with assistance from my Lathe, to make it faster.

After I am done, I will hook it on the same setup I had last night...and re-test it again.

Point here, is to find the right combination of gauge-turns and resistance in our whole setup...

This System does not work out with "whatever is laying around"...it must be BALANCED, and then we will have success.

On all Videos yesterday, I had the Coils loose on purpose, JUST FOR DEMONSTRATION ONLY, to be able to Visualize how this system "Pumps" in a Longitudinal way...and the huge force the Magnetic Fields displacement have.

However, if we allow the Coils to move, then our Virtual Field Displacement DECREASES in Spacetime gain.

So, no, this System is meant to work VERY COMPACT AND PRESSED TIGHT, in order that physical movement-displacement of our Coils do not take place!

While I was making the test, I compressed the whole assembly with my hands, and immediately it showed a noticeable gain, just by holding them tight, not allowing movement at low speed.

Even though -as you have noticed- when I increased speed, all coils tend to tighten by themselves.


Regards


Ufopolitics

[Ufopolitics]

Hello to All,

Please watch the difference from yesterday tests, when now, I just replaced the Secondary I just finished winding today...20 gauge, 14 Layers.

I will keep adding later on


Ufopolitics

[Ufopolitics]

Hello,

Now the last Test run for today, same Test Setup...but at 50V Input...

Ufopolitics

[Ufopolitics]

METHOD 2 (REPULSION) SYSTEM INTERNAL CONNECTIONS

Hello to All,

Ok, here I am showing the Magnetic Polarities, plus INTERNAL Connections Diagram, according to my Latest Setup, shown on last videos:

Description about CAD Drawing above:

1-I have set different Blues as different Reds to distinguish between the North-South belonging to FIELD 1 & FIELD 2.

2-Brush is positioned at contact #4. So, you can distinguish the advancement of North Field 1 versus North Field 2 at that specific point of contact.

3-As Positive charged Brush moves, following arrow direction, into further contacts 5, 6, 7, and 8, the Field 1 North (darker Blue) will keep displacing towards the Right, gaining proximity to Field 2 North (Lighter Blue).

4-As Brush passes Contact #8, and further on, according to directional arrow, the opposite displacement will take place, Field 1 North will start Retracting, as Field 2 North will start Expanding towards the Left, gaining proximity to Field 1 North.

Contacts 0 and 10, from Field 1 and Field 2 Coils END TERMINALS, are connected to DC Negative Input.
And these two contacts were the ones I split, in order to add Negative to Contact 0, and Positive DC to Contact 10, to demonstrate the FULL S>>>N Polarities of WHOLE ASSEMBLY OF COILS as ONE...And I disconnected Brush from positive for this test.

All this Test on Whole Coil Assy Polarity is demonstrated on my First Video, on previous page (27), Post 130.

Also, the Connections between Field Coils and Static Armature, Sequential Coils are shown on image, so "S" refers to START of Coil, as "E" represents the END of each Coil.

EDIT 1: PLEASE, NOTICE, the Connections between Field 1 and Static Armature Sequential Coils, and then the LAST Coil #7 START is connected to the START of Field 2 Coil.

I really do not have the full time to do it right now, but we need to get to a MUTUAL CONVENTION, as to "How can I determine my Coil is CW, or CCW?"

But I will say just the Basics here...

When You START to Wind a Coil, putting it in FRONT OF YOUR FACE, and looking at Your Hand wrist Watch, that is where you decide if you are winding to your RIGHT (CW) or to your LEFT (CCW)

All these CW & CCW Concepts, are PURELY RELATIVE, and ALWAYS they MUST come with "THE POINT OF VIEW LOCATION" in order to make sure you are doing it right.

For example: A 250,000 Testing Machine for Diesel Pumps, on its Software, in order to set the right Rotation sense, before testing, Machine gives you Two (2) arrows, one pointing Right and another one pointing Left...Then You must choose from Model# and Type of Pump You are testing...it will tell you on the Spec's, the Rotation Direction, PLUS, it will "ALWAYS remind you": LOOKING FROM THE FRONT CONNECTING SHAFT...And that is the POINT OF VIEW.

Meaning, that Pump, once already connected and plugged on Machine, shaft may be pointing AWAY from your Point of View....HOWEVER, You must always, imagine you are set IN FRONT OF PUMP, looking directly at its CENTER FRONT SHAFT, then "compute" the Rotation Sense...

Same thing happens with Vehicles, parts, replacements, alignment, repairs, etc,etc...They will always give you a "REFERENCE POINT" to locate the specific part...

On next Post I will be showing the way I connected, on this same image, but to Power Supply, and Scope Probes Location, Output V-Meter, etc,etc.


Regards


Ufopolitics

[Ufopolitics]

METHOD  2 (REPULSION) EXTERNAL TESTING CONNECTIONS

Hello there,

Ok, here is the Diagram of ALL External Connections on the latest Videos that I have shown...of course, Voltages for I/O varies, depending on Video Test, but in general, these are the connections for all Tests.

Next Test that I want to run, is to connect a Third Scope Probe (it would be Ch 2, Light Blue) to the Second Positive Input to Field 2 (Conn. #8)...I want to see both Input sinewaves simultaneously, next to each other's...in order to compare them.

And of course, ALL Probes are set at 1X, on ALL Channels, Volts Division on Scope settings = 2.5V also on all channels. (that volt div. is the best to be seen on video recordings)

Regards


Ufopolitics