Overunity Machines

Hello to All,

Well, about two years ago Pierre Cotnoir started a Thread at overunity dot com, as a month after, Holcomb presented all his Patents related to generating energy based on a Rotational Virtual Magnetic Field...

So, there was a lot of confusion trying to understand how these two systems worked. so, by being familiar with the operation, I posted a few explanations plus graphics at Holcomb and Pierre Cotnoir Threads about this Technology...and a lot of misunderstanding aroused, then I decided to ask Stefan to open for me a Moderated Thread, where I could disclose all my knowledge on the related tech.

I built a specific Model Setup, as a "Learning Tool", to demonstrate how these systems worked, plus all required CAD and Diagrams, the Thread was there until OU closed to read only...and by that time I made my discovery about the New Figuera Methods...so, I put this rotary system on a side, to start fully developing all Figuera Models.

Unfortunately, I did not copy the whole Thread and transfer it here, and by now Overunity Site is no longer available, not even to "read only"...

And now due to continuous developing on my Figuera Method, I came up with a new Figuera System Design that rotates 360º, however, FIRST, I need to revive this old thread from OU, so that the New Figuera approach would be much easier to understand.

Fortunately, I still have the Real Model setup, plus some of the Testing Videos that I uploaded on YouTube as "unlisted" two years ago (the originals are gone, because they were too large file sizes to keep on my PC) and majority of CAD and Diagrams, Images of the construction I have them, and will be posting them on this Topic.

So, I have made a new video resuming the Actual Model process and how it functions basically...





So above is the Graphic (shown on video) of the basic principle of this Setup. And here is showing a Universal Brushed Motor that we have fixed its rotor into the outer stator and are remotely rotating just the Brushes, on top of a static commutator, where all terminals are attached.

However, I have also specified that NOT EVERY UNIVERSAL MOTOR WILL WORK FOR THIS DEMONSTRATION, as it needs to be a LOW AMPS consuming motor.

In simpler terms, its armature windings need to be made with FINE GAUGE WIRE.

Also, that the Model shown here is definitively NOT A HIGH RESOLUTION FIELD ARRANGEMENT, but very Coarse, since it has only EIGHT PAIRS OF COILS, where each pair is located on the SAME SPACE, that I did in order to make it fit into a 20 slots rotor that I had.


A Higher Resolution displacing Field -with much better results- would be a 36 Coils set at 10º per step.

As many here are also familiar with this method, but a majority are not...it would serve as a re-learning process to understand that also a fully rotational virtual Magnetic Field can and will generate an Induced EMF on Secondaries.

Please, give me some time to finish the whole Topic Posts, before commenting here.

Regards to All

Ufopolitics

On the two images above I am showing the Two Different ways to setup Brushes electrical polarization to give us either a Wide Field Angle or a Narrow Field Angle.

The one that resulted best was the Narrow Angle setup.

WHY?...Because, like I explained on intro video above, my setup is based on a COARSE FIELD DISPLACEMENT, NOT a HIGH RESOLUTION, and WIDENING the Field Polarizations would render a weaker field than on the narrow angle.

For example: On Pierre Cotnoir, He had 36 Coils every 10 degrees, and had a total of SIX POLES first and then moved to Four Poles (which btw, did not worked)

My setup shown on video above that I would be showing all testing HAD ONLY TWO POLES, one North and one South.

Regards

Ufopolitics

And the Rotor-Armature I am using here for these tests is NOT the same 20 pole that I have shown before, however it is based on the same config of Eight Pairs of Coils.

So, after the results I decided to go for the Stator 1 Config...or Overlapped Type.

And the Diagram for the Stator Winding CAD:

Since I was not happy with the way brushes contacts were failing on previous test video, I adjusted brushes -tighter against commutator- to loose lesser contacting at higher speeds:

Hello to All,

I could also add here some building details, with images of the process of stripping the AC Induction Core, plus all winding process...but it is not needed because I am not going to be asking for anyone to replicate this setup.

This build had many flaws, like not enough coils switching over a Spacetime (Low Resolution Fields), plus the Driver was failing or loosing contacts at higher speeds, which are required to increase output...etc.

It was only built to show that YES, we CAN get an induction based on just rotating the Virtual Magnetic Field(s) at 360 degrees.

This Rotation System STRUCTURE is somehow very similar to the way a typical Generator Rotates its Exciter Fields, except that it rotates all Mass of Steel Core and Copper Coils included with Fields.

But it is definitively NOT the way to go, there is a LOT of wasted wire, that will never get induced at Stator Output and still will ADD A LOT of Resistance to the overall output circuit, HIGHLY RESTRICTING the OUTPUT CURRENTS FLOW.

Geometrically speaking, it is a "Momentary" Front-Facial Induction that takes place whenever exciter swipes Output coils ONLY at a specific alignment in a timed-angle.

The HUGE difference comparing it with the Figuera Type Geometry on my Method 2, is like Day and Night...where ALL LOOPS OF WIRE of the Induced Coil will get induced...

However, the Principle of a FULL CONSTANT ROTATION of Virtual Magnetic Field(s) at 360 degrees is the only part that could be used from this example.

All comments are welcome...

Regards

Ufopolitics