Overunity Machines

Hello to All,

I always loved this work done by Pierre Cotnoir!!

This Thread is still available for viewing only at: Pierre's 170W in 1600W out Looped Very impressive Build continued & moderated. (https://overunity.com/17653/pierres-170w-in-1600w-out-looped-very-impressive-build-continued-moderated)

This is the Second Thread that needed to be created by Gotoluc, because the lack of Moderation on Original one, just created a CHAOS. due to a lot of Annoying, Criticizing, and Noisy B.S Posts, NOT being Moderated properly!!

Actually, this Second Thread became also another chaos...ending in Member Peter1 (Pierre Cotnoir himself) leaving plus deleting all his videos on his YouTube Channel.

AND OF COURSE, ALL THIS NOISE, INTERRUPTIONS, NOT PROPERLY MODERATED THREADS/TOPICS ALWAYS RESULT/ENDS AS NO ONE BEING ABLE TO PROPERLY REPLICATE THIS WONDERFUL WORK!!

Until I finish Posting with all the Information that I have, it would be a "Read Only Mode Category/Topic"

Regards

Ufopolitics

Hello All,

First, I have uploaded ALL Four (4) Videos to my You Tube Channel in an Unlisted Playlist: Pierre Cotnoir DZ Generator Playlist (https://www.youtube.com/playlist?list=PLDK7GC_dPVjh00urQNj_01UC1f8jT7QDC), they are ALL UNLISTED, meaning, only people with the link, can see them, and of course you can always watch them here on our excellent You Tube Video Player included on all our Over Unity Machines Platform.

Here are some images from DZ Generator by Pierre Cotnoir:

Hello
this was my build-up. But it didn't work. I don't think it's going to work.



Greeting
Lota

Neues Projet DZ-Generator 2 - YouTube (https://www.youtube.com/watch?v=Kr-ydbHExoo)
Neues Projekt DZ-Generator - YouTube (https://www.youtube.com/shorts/B-SbtBOP7yQ)

Hello Lota,

Thanks for sharing here your excellent work!!

I have set Your two videos on your post, using the onsite YouTube Player, in order that people can see them here without having to go to YT...

Now, later on, (after I am finished with Figuera), if you allow me, I will help you to make it work.

Can you show image details about your Two Steel Cores, the Inner and the Outer set together?...front view to "virtual" center.

Thanks

Ufopolitics

Hello,
there are still the 3rd and 4th.

Hello All,

@Classic sent me this video by PM, thks Classic!...:


It is an "advanced" replication of the DZ Generator by Pierre Cotnoir, so I decided to post it here.

I called it "advanced" because it is using solid state electronic switching instead of relays, like Pierre used...

However, it is not working for him, although he is getting on output over 170 Volts...and you all could see that digital meter goes off once he connects a small halogen bulb.

In my opinion, this happens where there is no "juice" or amps on output...just higher than input voltage.

I have no idea how he is switching these coils, but I am seeing 6 switchers and a processor board...and it may mean that he has 36 coils.

These type of generators does not work like Figuera, they are fully rotary 360º, and there is a huge loss just by being this way.

So, that means, in order to be able to generate a higher amperage, everything must be "perfect".

First thing that I noticed he is doing wrong, is using a Generator Exciting Field Assembly (not modified) as the center coil that outputs.

In all my years working with magnetic fields, I have learned that you simply can not add more steel than just "required", basically off the Geometry that fields work...because the exciting field will get spread out of the main area where it must concentrate...and he is inserting gen exciter with steel the full shaft and the whole thing, even the bearings...

This kills the exciting field strength.

If you go to original video from Pierre, his center coil is just ONE Coil (Exciter he is using have Two Coil in series), plus it only have a center steel cross core, that you can barely see, unless he pulls it out.

Other thing I have no idea how he is doing it...is the sequencing.

Pierre DZ exciter coils work in pairs across, that CROSS FLUX in Diagonal and move that way for the whole 360...but video is in German...so, I do not understand how he is doing it.

Other than that it is a great and simple replication.

Regards

Ufopolitics

Hello All,

Two weeks ago, I started studying this device, and today, while reading, I had the sad realization that the overunity.com page was blocked. A Telegram channel appeared. I hope whoever took over the page will, at some point, give access to this valuable archive.

I hope this forum will not meet the same fate and, at some point, disappear.

Thanks

Spagiricus

Good time friends!

I visited this telegram channel. Along the way, complete ignorance of how a synchronous generator works in detail gives rise to .... "dancing on a rake"

The first generator with a mechanical rotor and a rotor without movement does not change the principle of indicating EMF. The task of a static rotor with switchable magnets is to repeat the work of a mechanical magnetic rotor.

Secondly, what is the principle behind the induction of EMF in the stator groove? Technically, the magnetic flux lines, the wire in the groove, are not cut. Why is the transformer EMF formula used to calculate the no-load EMF in a generator?Even in booklets about the basic structure of generators, "Basic Generator (https://ua-hho.do.am/_ld/0/22_2016-09-27-2-Ge.pdf)," the subtleties of the generator's operation to create an EMF and a sinusoidal signal are not disclosed. They are simply stating a fact.

Третье, почему игнорируете элементарные подобия, простейшего генератора с сердечником и генератора в укладкой в паз?

I indicated all the basic features of designing such a machine:

Wise Eye OverUnity: Electric generator with solid state magnetic rotor. (rakatskiy.blogspot.com) (https://rakatskiy.blogspot.com/2022/06/blog-post.html) 

I took it and clearly indicated where in the grooves the main turns of the phase should be laid:

Slide-1 (https://ua-hho.do.am/_ph/1/715950116.jpg); Slide - 2 (https://ua-hho.do.am/_ph/1/347841035.jpg)

______________________________________

Not everything that is declared in textbooks is true!

     

(Третье, почему игнорируете элементарные подобия, простейшего генератора с сердечником и генератора в укладкой в паз?)

Third, why do you ignore the elementary similarities of a simple generator with a core and a generator placed in a groove?

(https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhjGmeFveGVNqhCcSBdnmjg-Y778slVZAJVwXtfzPwqbrROsgFVvOU29cIyq7n7rYV0dHW8rdgTpfrNHhUibxVdg3NhEfchmSHwCwEmXC9DEGWO5a4I35ksnwUNCqmPTUQrO1F1SxFLEASDEFuIYNOFkcJf5wmL4S7GW2DadL9kdCjysrP9imaro9q7yYE/s1032/2023-11-09_085408.jpg)

The simplest generator with a core, find the position where the pole lines of force intersect the winding. By the way, one professor teaching electrical engineering told me why change the concept of education if such details are needed by a narrow circle of specialists who are engaged in design.

My sketches from back in 2015 for the project "Global Wave".

Figure 1 (https://ua-hho.do.am/_ph/1/287259980.jpg);  Figure 2 (https://ua-hho.do.am/_ph/1/431539741.jpg)

The final touch on the similarity.
Slide (https://ua-hho.do.am/_ph/1/670765395.jpg)