FIGUERA GENERATOR SEQUENTIAL DUAL (+/-) SOLID-STATE DRIVER DEVELOPMENT

[Ufopolitics]

@GreyWolf,

If you go to post:

FIGUERA GENERATOR SEQUENTIAL DUAL (+/-) SOLID-STATE DRIVER DEVELOPMENT - Page 4

You will see BOTH Drivers working...


Ufopolitics

[GreyWolf47]

UFO, Thanks for the quick reply and clarification on the sequencing. On my commutator, there are 16 contacts which make a sequence of 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16. They are jumper wired in pairs as 1-16, 2-15, 3-14, 4-13, 5-12, 6-11, 7-10, 8-9. This does not seem to match the sequencing of the new digital setup. The digital seems to give only one pulse to 1 and 8 but gives a double pulse to 2,3,4,5,6,7. It is my opinion ( limited as it is) that this will not give enough time to those pulses 1 and 8 to match the others.

I am not yet finished with my buildout of what I believe is a very true replication of Figuera's device with the 14 primaries and 14 secondaries with the primaries wound in separate mini coils in the same fashion that you do as coils over the secondary coil.
Thanks again for all you are doing to get this project completed.
GreyWolf47

[Ufopolitics]

UFO, Thanks for the quick reply and clarification on the sequencing. On my commutator, there are 16 contacts which make a sequence of 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16. They are jumper wired in pairs as 1-16, 2-15, 3-14, 4-13, 5-12, 6-11, 7-10, 8-9. This does not seem to match the sequencing of the new digital setup. The digital seems to give only one pulse to 1 and 8 but gives a double pulse to 2,3,4,5,6,7. It is my opinion ( limited as it is) that this will not give enough time to those pulses 1 and 8 to match the others.

Hello GreyWolf,

Thanks for sharing your analysis here!
Yes, I also noticed that sequence error on the Solid-State Driver(s), unfortunately by the time I mentioned it to Alex, He already had all drivers finished.

You have done an even deeper analysis here, and the result you found out is that we are only FULLY DOUBLE Pulsing Six (6) Coils per Cycle (2, 3, 4, 5, 6, 7).
If we carefully look at short video with the incandescent light bulbs at SLOW MOTION 180%, we can clearly notice that the end bulbs [1 & 8] are not getting a full illumination:

However, this issue has a simple solution without having to modify the design of the driver(s)...

And that is to REDUCE the RESISTANCE on Coils One (1) and Eight [8], by simply a couple of Ohms less or a few lesser turns.

This will cause that Currents (Amperage) Increase only at those two points [1 & 8] and so Magnetic Field will also Intensify or gain strength at both end points.

So, that will "compensate" the shorter time ON, at those two intervals with Higher Currents rushing in.

I am also pretty sure this also have a simple Electronic Solution at the two end output points, as a small capacitor would delay the timing at those two points.

But here @kampen will give us the professional solution to this matter.

I thanks you again, @GreyWolf for bringing this up, as now I am working precisely on getting the sequential coils mold pattern for my Linear Setup.

Regards

Ufopolitics

EDIT 1: I still have to CALCULATE this issue in more detail, about the resistance reduction at the end coils #1 & #8...because I want to ALWAYS have a Total of 50 Ohms on Eight Coils at ALL TIME during the sequencing on my latest Linear Dual Pulsing (-/+):

[Ufopolitics]

I am not yet finished with my buildout of what I believe is a very true replication of Figuera's device with the 14 primaries and 14 secondaries with the primaries wound in separate mini coils in the same fashion that you do as coils over the secondary coil.
Thanks again for all you are doing to get this project completed.
GreyWolf47

Hello again GreyWolf,

Now, if as you have mentioned above (on bold and underlined statement by me) that you are making a "true" replication of Figuera's Device...

I must remind you that Points 1 and 8 -as Figuera 1908 Patent- are direct positive flow to Primaries, meaning, no resistance, no coils involved on those two points (1-16) (8-9) regardless of timing sequence.

On these two points primaries electromagnets receive FULL POWER.

Ufopolitics

[GreyWolf47]

UFO, Thanks again for that information. I will be posting some schematics on my thread soon so as to not clutter up your work here. I will say here that ALL primary coils receive the full 12 volt directly from the commutator with no resistance but in a ordered sequence that moves the flux first increasing in one direction and then decreasing back to zero and then the sequence starts at the opposite end of the same primary increasing in 4 steps and then back to zero.
Thanks again
GreyWolf47