FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello again,

Here I have uploaded the video about the Test I have mentioned on prior post...

I have added Scope Probe #2 (light blue) to the Input terminal 8, for Field 2...and I am showing both Input sines...

Regards

Ufopolitics

[Ufopolitics]

Hello,

And here is that test...removing connector #8 from commutator Positive Power to Field 2, leaving Probe and cap connected...to see the blue sine now:

So, the question here is, what is the source of ENERGY feeding this blue sine?

1- It could be through EM Induction from other Coils active, plus displacing still, back and forth?...

2- Or it could be from Series Connection that still, electrically activates Field Coil 2...but if so, IMHO, Both sines should be in sync, aligned, correct?...

Not Offset like is showing after disconnection...

And there is a way to find out...disconnecting coil #7 from Field Coil 2...and reading just from Field Coil 2...

If it still there (Blue sinewave) after disconnecting Coil 7, then it is purely EM Induction.

and also (maybe on a forth channel) from disconnected terminal from coil 7....to read that Signal.

Regards

Ufopolitics

[Ufopolitics]

So, the question here is, what is the source of ENERGY feeding this blue sine?

1- It could be through EM Induction from other Coils active, plus displacing still, back and forth?...

2- Or it could be from Series Connection that still, electrically activates Field Coil 2...but if so, IMHO, Both sines should be in sync, aligned, correct?...

Not Offset like is showing after disconnection...

And there is a way to find out...disconnecting coil #7 from Field Coil 2...and reading just from Field Coil 2...

If it still there (Blue sinewave) after disconnecting Coil 7, then it is purely EM Induction.

and also (maybe on a forth channel) from disconnected terminal from coil 7....to read that Signal.

Regards

Ufopolitics

Nevermind...I tested.

That Blue Sine is there because of Both...1 & 2...

From coil 7 is weak, but there, offset...and when connect Field 2 it maximizes...

Regards

Ufopolitics

[greybeardmike]

ufopolitics,
The phenomena that you are showing is what I talked to you about in an email that I sent you a few days ago.  I think to determine was is happening here is something that I was trying to do when I blew up my mosfet driver board.  Awaiting parts to rebuild.

I think you should try breaking your system apart into two pieces.  It will require another core and another secondary/ armature/y coil.  Separate the two coil sets completely, physically, then drive them with the commutator just like you are doing now in the opposing directions.  With a restive load on each y coil the output should be measured and observed.

Then connect the two y coils together with the polarity to create a sine wave.  I think that feedback voltage (Lenz's law or Lorentz law) from the active coils will be absorbed in the permeance of the inactive coil.  The two field coils that you refer to may need a small current in the inactive state to create permeance, although remnant magnetism in the core may be sufficient.

The fields in the cores will never change direction, only in strength.  The only thing changing direction will be the current and voltage in the y coil.

I don't think this is a violation of Figuera's design because the patent is very (intentionally) vague on the construction of the coil sets.  That's how patents work.

That is the approach I am working on a painstakingly slow pace.  I'm no expert on electromagnetism so anyone feel free to comment.

Keep up all the good work.  Your enthusiasm is contagious.

greybeardmike

[Ufopolitics]

ufopolitics,
The phenomena that you are showing is what I talked to you about in an email that I sent you a few days ago.  I think to determine was is happening here is something that I was trying to do when I blew up my mosfet driver board.  Awaiting parts to rebuild.

I think you should try breaking your system apart into two pieces.  It will require another core and another secondary/ armature/y coil.  Separate the two coil sets completely, physically, then drive them with the commutator just like you are doing now in the opposing directions.  With a restive load on each y coil the output should be measured and observed.

Then connect the two y coils together with the polarity to create a sine wave.  I think that feedback voltage (Lenz's law or Lorentz law) from the active coils will be absorbed in the permeance of the inactive coil.  The two field coils that you refer to may need a small current in the inactive state to create permeance, although remnant magnetism in the core may be sufficient.

The fields in the cores will never change direction, only in strength.  The only thing changing direction will be the current and voltage in the y coil.

I don't think this is a violation of Figuera's design because the patent is very (intentionally) vague on the construction of the coil sets.  That's how patents work.

That is the approach I am working on a painstakingly slow pace.  I'm no expert on electromagnetism so anyone feel free to comment.

Keep up all the good work.  Your enthusiasm is contagious.

greybeardmike

Thanks Mike,

Please do not take me wrong, but I am happy with what I have so far...and the System is still not completed. So, at this point, I am not trying to "repair" the "electrons magnetic pump"...

I still have to finish the rest of sequential coils at 3.0 ohms with 23ga...to have a FULL view of the whole system operation, completed, before I make any radical changes.

This design works better with the TWO Opposite Fields moving back and forth at Unison, on the same core, on the same secondary coil, and it is easy to know, just disconnecting one side Field (2)... the output on "y" drops...like I did on previous videos...

The tests I have been doing about the point 8 terminal probe, and Field 2, is just to determine if both sequential Groups are "Self Inducing" between themselves on the lapse of time, when one is greater in Field intensity over the second one...So, I still have another pending test to make.

NEXT TEST: I am going to fully disconnect Field 2 Coil, also from negative, so both terminals would be scoped while system is running, then I would know the signal that Field 2 is generating, which would also apply to  Field 1, obviously if they are both identical sequences, just offset on their operation.

On another note, Yes, I am going to build another set, identical to this one, since I already have another two Field Coils, with identical spec's as the ones on this system...but I need to order more 20 gauge wire for the 2nd secondary.

I still have plenty of 23 gauge wire.

About your blown FET's...try using Optocoupler's, to feed the Gates of your MOSFET's, as also use safety diode's between Drain-Source...

Regards


Ufopolitics