FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello All,

This post is about the way that I will make the future tests by using the existing Fifteen (15) Sequential Coils that I have already built.
Fifteen (15) Coils are Divisible by Three (3).
Each one of these Sequential Coils have 6.25 Ohms Resistance.

However, I will be making TWO TESTS:

1: THE SYMMETRIC TEST

• The Symmetric Test, where the Division would be done by Grouping Five (5) Coils (5-5-5)
• Each Group of Five Coils in SERIES.
• Where All Three Groups will have the same Total Resistance of 31.25 Ohms Each.
• However, the Voltages would NOT be distributed Equally.
• The Center Coil Q3 will receive around HALF of the Resistance Value, or 15 Volts.
• This Relationship of V/R would generate a Current of 0.5 Amp.
• While the Coils Q1 & Q2 (of same Resistance as Q3) would be powered by around the SAME Voltage, or 31 Volts
• These relationship of V/R on Q1 & Q2 would generate a Current of around 1.0 Amp.
• Except, whenever there would be a Transition (Tx).
• Which for the Q1 & Q2 will LOWER Resistance to 15.625 Ohms.
• On these Q1 & Q2 Transitions, the Currents will increase to approximately 2.0 Amps (31.25V/15.625 Ohms)

2: THE ASYMMETRIC TEST

• The Asymmetric Test, where the Division would be done by Grouping Q1 & Q2 with SIX (6) Coils.
• While Q3 would be only THREE (3) Coils
• As ALL Three Groups would also be connected in SERIES between their Internal Configuring Coils.
• Where All Three Groups will have DIFFERENT Resistances.
• Q1 & Q2 would have 37.5 Ohms
• While Q3 would only have 18.75 Ohms
• And also (as previous test), the Voltages would NOT be distributed Equally.
• The Center Coil Q3 will receive around HALF of the Resistance Value, or 9 Volts.
• This Relationship of V/R would generate a Current of around 0.5 Amp.
• While the Coils Q1 & Q2 would be powered by around the SAME Voltage as their Resistance Values, or 37.5 Volts
• These relationship of V/R on Q1 & Q2 would generate a Current of around 1.0 Amp.
• Except, whenever there would be a Transition (Tx) (Parallel Connection of Q1 & Q2)
• Which for the Q1 & Q2 will LOWER Resistance to 18.75 Ohms.
• On these Q1 & Q2 Transitions, the Currents will increase to approximately 2.0 Amps (37.5V/15.625 Ohms)

These Two Tests will basically play with the Field Spatial Volume differences, between the Three Coils.
Because I would try to keep currents around the same values for BOTH Tests.
Where Q1 & Q2 would have around 1.0 Amp, whenever powered for the Two Tests
And Q3 around 0.5 Amp.
As for BOTH Tests, the Transition Currents would increase EXACTLY at 2.0 Amps.

RESUMING: I will use the TWO SEPARATED Voltage SUPPLY UNITS as the 'Voltage Regulator' to keep these currents identical for BOTH Tests.
Because, as I mentioned before, Q1 & Q2 would be powered by a SEPARATED PSU than Q3 for BOTH Tests.
These Two Tests will give us -based on their OUTPUT results- which one will cause a greater and more robust INDUCTION on the Main Secondary. (I still have not made FC1 & FC2)

Regards to All

Ufopolitics

EDIT 1:  For BOTH Tests, the Mechanical Commutator Driver would be wired for Four Full Cycles per Revolution, therefore, to reach the 60 Hertz, it will just need to spin at 900 RPM's.