FIGUERA'S AETHER MAGNETIC FIELDS LINEAR PUMP, REVIVED

[Ufopolitics]

Hello to All,

Ok, I was able to isolate the Exciter's Self Induction...

This time I only used two diodes from the AC Cap... opposite to positive and negative (not allowing input -/+ to go through) then added the E-Cap, then another set of diodes to inject to DC Input...so, input does not return to E-Cap.

And what happens is that it "chops" the peak Input Sine, into a type of chopped pyramid signal...which, of course drops output.

After reviewing all this, then I realize that Input signals are NOT a true AC sine, it only runs on the positive side...so, when processing it through rectifiers and diodes...it ends up chopping the main input signal.

Conclusion, to have a self-feeding generator, we do need to add a specific secondary(ies), which generates a true AC sine, like the inner secondary does.

What is a fact, is that by collecting these specific excess DC from the exciters, the whole system works better, cooler, and input signals are also cleaner.

I will try tomorrow to put a simple diagram about what I have explained above. Plus, I want to see that Signal (after is separated from Exciter System), in a Fourth Probe.

Regards

Ufopolitics

[Ufopolitics]

Hello everyone!

Ok, I already made the video, upload it, plus the CAD Diagram related to Testing the Exciter System Mutual Induction, as I was able to isolate it from Input with just two diodes for each AC Cap Banks.

As you can see, I have connected a Forth Probe to read the signal coming out from one bank, through the diodes blocking the input...is Channel 4, darker blue.

Plus also an AC Meter to read the Output from Exciter's Coils.

And here is the video about this test:

As also on video is shown that when I connect both positives after diodes, the Positive only sine at fourth channel, becomes a full sine, because it is capturing the full reciprocating cycle, of the movement of Both Fields.

However, we have learned that this extra energy from exciters is NOT to be drained in any way or form, because it will cause for Exciting signal to drop to a chopped sine, reducing the main Secondary Output as well.

That is the reason why, I connected a small motor to just one of the AC Sine banks...to observe the results, as it chopped the input signal corresponding to this bank (point 1 contact on commutator).

Regards

Ufopolitics

[Ufopolitics]

Hello again,

Ok, I have decided to run a Second Video, in order to show clearer about the output from the Exciter System in detail.

First, each bank signal captured on Channel 4 MATCHES identically to that particular side bank being measured...or:

1- Point 1, Contact 1 on Commutator, attached to Field 1...is the Magenta Channel.

2- Point 8, Contact 8 on Commutator, attached to Field 2...is the Light Blue Channel.

So, when I set one of the specific points cited above, the Positive Signal from Channel 4 Peak (darker blue, bottom on screen), matches perfectly to the Input Sine Peak of the respective signal on that point.

However, whenever we jump (after diodes) JUST the two positives ONLY, then we get a perfect sinewave that goes from positive to negative, and still, ALL PEAKS, matches exactly with Both Input Signal's Peaks.. All this done WITHOUT affecting at all, the Output or the Exciting Signals.

Regards

Ufopolitics

[Ufopolitics]

Hello,

Ok, this short video, is about demonstrating what I have said on previous video, about what happens whenever we join Point 1 with Point 8 on the Two Banks directly.

Which is exactly as jumping commutator points 1 and 8.

That I said that whole system dies...because it will kill all magnetic back and forth, all unison, and everything will collapse...

So, on this video you will see that happening.

Which fully demonstrates that whenever I join, after the two diodes (back end of system), the two positives, and systems keeps running perfectly alive, like nothing ever happened...we are just joining the REACTION from all Coils on the Sequence, NOT directly from contact 1 and contact 8.

Regards

Ufopolitics

[Fessor]

Hi Ufo,

its amazing, so very well done and thought out.

Your sine on C1 and C2 may be alternating voltage and not current, as it is feed purely from the DC side, dont you think?. Your scope shows a zero line, but don't you think it's the scope that misinterpreted AV as AC? Could be concluded with yet another diode preventing negative side/current, or am I misunderstanding your diodes and measures already done here?

In one video you state to still have a cap on the output side, Yellow secondary, correct? If so, why? and what would it look like without when it is now running so smoothly with low amparage on input?  I wonder if this cap is making a kind of positive interference with the total unison generation, hence, what's the effect without?

Finally, I still don't get the effect of your inputs fall to below zero, this effect I think is worth to investigate as well, kind of unforeseen falling momentum to below zero. Could it be? the scope that is having a hard time to detect actual zero for the various channels?

Fessor