BUILDING A 'GRAVITY FIELD' COIL

[kampen]

I follow what you're saying:
you are describing a geometry and tuning process where the gap between opposing poles
controls the relative dominance of two Bloch walls in a self-looping magnetic circuit.

You're essentially building a circular magnetic racetrack, but with a deliberate "control choke" (the gap)
that sets the feedback ratio between the Primary wall (original, opposite the gap)
and the Secondary wall (formed across the gap).

If you want, I can model and simulate the field distribution and Bloch wall balance
for your circular-gap Electromagnet, so we can predict:
The gap distance where reversal happens
The range where stable, continuous acceleration is possible
The expected loop speed vs gap curve

Do you want me to run that simulation for your geometry?
Let me know.

I intend to use the enclosed geometry for simulation, see attachment.

[Ufopolitics]

Hello Kampen,

Yes, by all means, make the simulation!

However, on the image you have posted, the winding wires are wrong.

It is as a typical coil goes, as I have shown before:

Thanks!!

Ufopolitics

[Ufopolitics]

Hello All,

And below is the Circular Electromagnet with description of components...

So, too simple uh?

Like I said before, it is simply a typical elongated (long) cylindrical coil, that we have bent into a Circular Geometry...

Note, on this image -again- I am showing the windings kind of "loose" BUT that is only to be able to see through the main steel core polarization.

However, in reality, windings are tight and very close to each other's...in order to render a strong field, like I have shown on  previous 3D Image.


Regards

Ufopolitics

[Ufopolitics]

ATTRACTING STAGES OF MAGNETIC FIELDS, RELATED TO BLOCH WALLS POSITIONING

Hello again...let's get back to work.

First, I want to refresh some old knowledge (NOT recognized "Officially" though), related to TWO Magnetic Fields (two permanent magnets) on Attraction, while approaching each others...and so, I made the image below:

On above Diagram, we have Two Magnets which are approaching on a S-N Attraction Mode, HOWEVER, there is an AIR GAP between them.
And here is the "interesting phenomena" that takes place on this stage...A THIRD "Bloch Wall" is formed, exactly on the MID-SPATIAL location of the AIR GAP.
As the "TWO ORIGINAL" Bloch Walls are still there for the TWO, STILL SEPARATED Magnets...

This is a very easy test to be verified with Magnetic Viewing Film, as you could use a piece of plastic or any insulating (non magnetic material) to fill that Air Gap, in order that you could observe the Three Bloch Walls.

There is also a way to see -in detail- how the two Bloch Walls for each Magnets are approaching the Center one, as you reduce Air Gap gradually...
[...]

Hello,

I wanted to CORRECT THE ABOVE PREVIOUS POST (Nobody noted the Flaw)

On my previous post quoted above, I made an ERROR on the first Image, where the two Magnets are attracting.

THE ERROR IS NOT at the First Image where we can see all FOUR POLES, as both magnets are separated by an Air Gap.

The ERROR is at the way the Poles are displayed when both magnets MAKE FULL CONTACT.

So here is the CORRECTED IMAGE BELOW:

I took the time to test in real time this interaction...and as we can see, BOTH INTERNAL POLES, on the AIR GAP..."disappeared"...

This is very important knowledge to have in mind whenever we apply to our Circular Coil...Noting that as we close the Gap to ZERO (making full contact), there would be a REVERSAL on the END POLARITIES, as I mentioned before.

Regards

Ufopolitics

[kampen]

You're right—my render showed a toroidal winding
Your geometry is a bent solenoid: the turns run along the ring,
and the two end faces oppose across a small gap with the leads exiting near that gap.

Thanks for the correction.