Using Permanent Magnetic Potential Energy as a main power source only

[Dr.Wlazlak]

Building a machine that runs on Permanent Magnetic Potential Energy alone:
is said to be Impossible by science: however it is possible using the 
EttCM energy technology:: Energy to torque Conversion Magnetic :: method 
of decreasing and increasing the attraction to ferrous or iron type metals in a 
motor type design engineered to used this technology as a power source of 
output energy usable for many types of designs and concepts.

There will be a recap on the method presented on this string showing the simple
concepts of decreasing and increasing magnetic pulling power on the 
Ferrous induction plate being the same type used and shown in other devices on
the designs of the EttCM energy technology motor systems

( This method of decreasing and increasing the magnetic pull force is the basic concepts of how to make a workable type system: without this method there could be not change in the magnetic power between the input and output on the induction field plate: and no decreasing then would not conform to the laws of thermodynamics: ( But having it possible to decrease and increase::: also makes it possible to conform to all the laws of Physics and thermodynamics; and the Google AI has confirmed this to be true:: on the EttCM energy technology:)

The design below does not use ( Gravity on the design ) it is a totally magnetic system only making it about 10,000 time more powerful per size than a gravity system of concept: Plus: A whole lot simpler to build a workable machine: 

Again: the recap of the main energy source; First:
Having 2 sets of magnets that a the same poles pushing together having 2 times pushing against 1 single magnet produce an almost zero attraction to iron or ferrous metals ( having them apart as shown above returns the single magnet to normal power of attraction to the ferrous metals ) showing 2 Lbs. pull above

 
As shown when the 2 magnets are push close together the power of attraction produces ( Less attraction to the iron plate ) showing 1/4 Lbs pull

On the drawing below the iron bars can move on back and forth as shown
the magnets are fixed not to move as shown 
This shows how the power of attraction produce more pull on One side and less on the other side -- doing the same effect on a motor type design allowing the movement of rotation to this type of offset power factor:


On the drawing below is shows how the magnets are pulled into the ferrous induction plate on a simple concept design as an example of how a motor works in the same type of action;

Notice: on the Left side the input pull is 2 Lbs. this was shown on a test on another string and post; The right side is 1/4 Lbs backward pull --- at a much lesser force making the pull power greater - and allowing a motor type device to be built that uses this method where it can be powered by Permanent magnetic potential energy ( alone ) as the main and only input power - built into the device - that will run on its own power source for many years. produce usable output power.

The next Post will show a concept design that used the method; and like the motor that uses Gravity and mercury weight were the wheel is always in balance this system does the same thing ( but does not use gravity or liquid weight in the design)  

[Dr.Wlazlak]

The motor design below is a simple type radial design using a crank shaft type system to move the magnets apart and close together as the induction plate rotates
much like a gas powered engine the magnets are in cylinders and they move back and forth inside the cylinders 

Because all the magnets are evenly being push apart as they are the same poles facing each other inside the cylinders the wheel system is always in balance taking very little energy to make the decrease and increase of power of attraction to the induction plate; ( working in the same way of balance as the Gravity / mercury weight system does ) on no gravity or liquid is used in this design -

( if there are any question ) please fell free to ask on this string: 
The arrows show the force of being pushed equal on each side making it balanced allowing the machine to use very little energy to make the decrease and increase of energy for the motors use


like all the EttCM induction motor designs the steel plate is used to attract magnetic force into movement in a rotary motion: a constant pull of 1 and 3/4 Lbs. makes usable output power overcoming friction: and producing usable output power 

Again: running on Permanent Magnetic Kinetic energy as the only power source:

As close to Perpetual motion as is possible; But again: NOT a perpetual motion machine

( EttCM energy technology ) Energy to torque Conversion Magnetic technology 
No confusion to the science community is needed: ( thank you)